Filter
Top Products
18
19
VCR to a Cable Box
Figure 6
A two-way RF splitter, 4 coaxial cables, right and left audio
cables and an S-Video or Video cable are required. These are
not included with the TV.
1. Connect the incoming cable to IN on the RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the cable box back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to ANT-2 AUX on the TV back panel.
4. Connect one coaxial cable from OUT on the cable
box to ANTENNA IN on the VCR back panel.
5. Connect one coaxial cable from ANTENNA OUT on
the VCR back panel to ANT-1 MAIN on the TV back
panel.
6. To use the TV speakers with the VCR, connect a
set of audio cables from AUDIO OUT on the VCR
back panel to INPUT 1 AUDIO-LEFT (MONO) and
AUDIO-RIGHT on the TV back panel. The red cable
connects to the R (right) channel and the white
Figure 6. Connecting a VCR to a Cable Box
TUBE
R
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUTPUT
AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM
SLOT
– (DTV/CABLE /VHF/UHF) –
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT MONITOR OUTPUT
AUDIO 21 2
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
Digital Video
Digital Audio
Analog Audio
S-Video
recommended
if available
Attach
only
one
cable
type
TV back panel
6.
5.
ANT-2
AUX
– (DTV/CABLE /VHF/UHF) –
7.
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT
1 2
ANT-1
MAIN
IN
OUT
OUT
TWO WAYSPLITTER
Incoming Cable
1.
2.
3.
MONITOR OUTPUT
AUDIO/VIDEO 1
9.
3.
8.
Cable Box
back panel
section
IN
OUT
2.
4.
9.
HS-U748
VCR back panel
If your VCR has a video channel
or RF ON/OFF switch, set it to OFF.
7.
6.
7.
8.
5.
4.
S-Video
recommended
if available
White
Red
White
Red
White
Red
W
h
i
t
e
R
e
d
Attach
only
one
cable
type
Note: NetCommand® will assume your VCR is connected to inputs as shown here. If you
use any other inputs for your VCR or add a second VCR this change must match in the
NetCommand system. See Edit NetCommand... pages 35-42 for more information.
Connecting VCR Video and Audio to a Cable Box
cable connects to the L (left) channel. If your VCR
is mono (non-stereo), connect only the white (left)
cable.
7. Connect either an S-Video or Video cable from
VIDEO OUT on the VCR back panel to INPUT 1
VIDEO on the TV back panel. Only one type of
video cable should be connected. S-Video is
recommended, if available.
8. For NetCommand® controlled recordings, connect
a Video cable from VIDEO IN on the VCR back
panel to MONITOR OUTPUT AUDIO/VIDEO 1 on
the TV back panel.
9. Complete the NetCommand controlled recording
connection by connecting a set of audio cables
from AUDIO IN on the VCR back panel to MONITOR
OUTPUT AUDIO/VIDEO 1 AUDIO-LEFT (MONO)
and AUDIO-RIGHT on the TV back panel. The red
cable connects to the R (right) channel and the
white cable connects to the L (left) channel.