Mitsubishi Electronics WD720U Projection Television User Manual


  Open as PDF
of 61
 
EN-35
5. Select OK, and NEW NETWORK PASSWORD
screen appears if the entered password is correct.
• Iftheenteredpasswordisnotcorrect,the
CURRENT NETWORK PASSWORD screen
appears again.
← →
↔
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗
NEW NETWORK PASSWORD
CONFIRM NETWORK PASSWORD
OK
caps
CLEAR
DEL
CANCEL
B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
0 1 2 3 4 5 6 7 8 9
A
6. Enter the NEW NETWORK PASSWORD and
CONFIRM NETWORK PASSWORD.
• Passwordcanbesetusingupto32characters
including alphabets (capital/small) or numeric
characters.
← key: Shifting the position of enter
cursor to the left for each
character.
→ key: Shifting the position of enter
cursor to the right for each
character.
key: Shifting the position of
enter cursor between NEW
NETWORK PASSWORD
and CONFIRM NETWORK
PASSWORD.
DEL key: Deleting the character in the
position of enter cursor for each
character.
caps/CAPS key:
Switching an alphabet character
to CAPITAL or small.
CLEAR key: Deleting all the entered
characters.
7. When NEW NETWORK PASSWORD and CONFIRM
NETWORK PASSWORD are matched, the setting is
completed after changing the Network Password.
• Iftheenteredcontentisnotmatched,NEW
NETWORK PASSWORD screen appears again
after an error dialog is displayed.
• Itmaytakesometimetoreectthesettings.
IP Config settings
(See page 22 for menu setting.)
1. Display the Network Config menu.
2. Press the or button to select IP Config.
IP Config
OK
3. Press the ENTER button.
• TheIPCongmenuappears.
MENU
IP Config
Adjust Exit
Select
DHCP
IP Address
Subnet Mask
Default Gateway
MAC Address
DHCP Function
Start IP Address
End IP Address
IP Config Setup
On
OK
xx-xx-xx-xx-xx-xx
Off
169
-
-
-
255
169
254
-
-
-
255
254
0
-
-
-
0
0
220
0
169
-
-
169
254
-
-
254
0
-
-
254
221
254
1
Setting or clearing DHCP
1. Display the IP Config menu.
2. Press the or button to select DHCP.
DHCP
On
3. Press the or button to select On or Off.
• Tocancelthesetting,presstheMENUbutton.
• WhenDHCPissettoOn,IPAddress,Subnet
Mask, Default Gateway, and DHCP Function
cannot be set. If you want to set these settings,
set DHCP to Off and perform the IP settings as
follows.
IP Address settings
1. Display the IP Config menu.
2. Press the or button to select IP Address.
IP Address
169
-
254
-
0
-
220
3. Press the ENTER button.
• Therstoctetisselected.
IP Address
169
-
254
-
0
-
220
4. Press the or button to select the numeric
value.
5. Press the or button to select the octet.
• Thesecondornaloctetisselected.
IP Address
169
-
254
-
0
-
220
6. Press the ENTER button.
• Tocancelthesetting,presstheMENUbutton.
• Setthenumericvaluewithintherangefrom0to
255. However, set the numeric value for the final
octet within the range from 1 to 254.
Network settings (continued)
 previous next