Filter
Top Products
17
EN
INDEX SEARCH
0 3
TIME SEARCH
2 : 50
TIME SEARCH
TV/VCRTV/VCR
This function allows you to quickly
advance the tape to your desired posi-
tion simply by entering the exact amount of playback
time you want to skip.
In the example below: To watch a program before/
after 2 hour 50 minutes from the present position,
in either direction.
1 Press [SET-UP].
Use
[
KK
/
LL
] to point to "TIME
SEARCH", then press
[ENTER].
2 Use [
KK
/
LL
] until your desired
time appears.
To cancel the Time Search at
this point, press
[SET-UP].
NOTE:
•Time Search can be set up to a maximum of 9 hours
50 minutes (9:50) by 10 minutes at a time.
3 Use [
ss
/
BB
] to rewind or fast forward to the
specified point.
The time counts down during the search. When
the counter reaches "0:00:00", the tape will start
playback automatically.
TO CANCEL DURING TIME SEARCH
Press [STOP/EJECT C A] on the unit or [STOP
CC
].
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B TIME SEARCH
INDEX SEARCH
INDEX SEARCH
TV/VCRTV/VCR
This function allows you to index the
starting point to make it easy to reach
the point in either fast forward or rewind mode.
•Every time you start recording
, an index is marked
automatically. The index mark also works as the
starting point of Timer recording and OTR.
• The index mark will not be recorded if
[PAUSE
FF
]
is used during recording.
• The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 min-
utes for SLP recording.
• In some cases, the index mark at the beginning of
video tape cannot be detected.
Example: You are watching program number 4 and
want to fast forward to program number 7. Skip
three programs.
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7
4321123
End of
the tape
Beginning of
the tape
CURRENT PLAYBACK PROGRAM
INDEX MARK
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B INDEX SEARCH
1 Press [SET-UP].
Use
[
KK
/
LL
] to point to
"INDEX SEARCH", then press
[ENTER].
2 Use [
KK
/
LL
] until the number
of programs that you want to
skip appears.
3 Use [
ss
/
BB
]. The unit begins rewinding or fast
forwarding to the beginning of desired program.
4 When the search is completed, the unit will start
playback automatically.
• The numbers of Index Search can be set up to
20.
• This function is not available during recording.
TO CANCEL DURING INDEX SEARCH
Press [STOP/EJECT C A] on the unit or [STOP
CC
].
PICTURE SEARCH
TV/VCRTV/VCR
This function is useful in finding or
skipping over a particular scene on a
tape. In this mode, the sound will be muted.
1 During playback, press [REV
EE
] or [FWD
DD
]
to view at a high speed (in forward/reverse).
2 Press [REV
EE
] or [FWD
DD
] again to view at
super high speed (in LP/SLP modes only).
NOTE:
•Tapes recorded in the SP or LP mode will normally
display a noise bar on the TV screen and the picture
may revert to black and white.
3 Press [PLAY
BB
] to return to normal playback.
SPECIAL PLAYBACK / SEARCH FUNCTION
TV/VCR SECTION
T1200UA_EN.QX3 06.2.6 11:16 AM Page 17