Filter
Top Products
VCR Functions
EN
–
13
–
10
Press [SUBTITLE/T-SET] to set timer standby mode.
• indicator on the front panel lights up. The unit will
change to the DVD mode.
6
Select “AM” or “PM”.
Then press [B] to go to next step.
7
Repeat the procedure in steps 5 and 6 to set the end time.
8
Select the desired channel.
Then press [B] to go to next step.
• If you have connected the unit to a cable box or satellite
box as the connection on page 6, select the VCR to
channel 3 or 4 (the RF output channel of the VCR). Then,
select the desired channel at the cable box or satellite box.
Leave the cable box or satellite box on for Timer Recording.
9
Select the desired recording speed, then press
[CLEAR/C.RESET].
• To set another program after step 9, press [B].
Then, continue with step 2.
Hint
• To go back one step, press [s] during steps 3 to 9.
To Check, Correct or Cancel a Timer Program
1) Press [SUBTITLE/T-SET] then, [VCR] on the remote
control.
2) Select main menu by pressing [MENU].
3) Select “TIMER PROGRAMMING” by using [K/L], then
press [B].
4) Select the program number which you want to check by
using [K/L]. The details of the program you selected will
appear on the TV screen.
• Go to the digit you want to change by using [s /B].
Then, enter correct numbers by using [K/L].
• You may cancel the entire program by pressing [s]
while the program number blinks.
5) Press [CLEAR/C.RESET] to exit.
6) Press [SUBTITLE/T-SET] to return to timer standby
mode.
To cancel a Timer Recording in progress
Press [STOP/EJECT C A] on the unit.
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
AM
B PM
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED SP
B SP
SLP
SUBTITLE
T-SET
Hints for OTR and Timer Recording
or
or
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED – –
or
CLEAR/
C. RESET
• Press [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR
mode, then press [SUBTITLE/T-SET].
• If a tape is not in the unit or does not have the record tab, indicator on the front panel blinks and Timer Recording
cannot be performed. Please insert a recordable tape.
• When Timer Recordings are set, indicator on the front panel lights up. To use the VCR as usual until the time for the
recording, press [SUBTITLE/T-SET] so that indicator lights off. Press [VCR/TV] to choose the VCR position. Select either
VCR or DVD mode, then continue with the other features as described in this manual.
After an OTR or a Timer Recording has been set, this unit operates as follows:
• If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape. Press [SUBTITLE/T-SET] on the
remote control or [STOP/EJECT C A] on the unit, then press [VCR] to activate the VCR function again.
• Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET] is pressed.
• To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then
press [VCR] to activate the VCR function again.
• The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after
you canceled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you
operate.
When an OTR or a Timer Recording is completed...
• If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically,
and
indicator on the front panel lights to indicate the unit is in the timer standby mode.
• indicator on the front panel flashes if there are no more Timer Recordings on standby.
• If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR functions will be
unavailable. All the DVD functions are available during OTR, timer standby mode and Timer Recording.
• Press [STOP/EJECT C A] on the front panel or [SUBTITLE/T-SET] on the remote control to use the VCR when the unit is
off.
• Press [OUTPUT] on the front panel or [VCR] on the remote control to use the VCR when the unit is on. In case Timer
Recording is in standby mode, press [STOP/EJECT C A] on the front panel or [SUBTITLE/T-SET] on the remote control,
and then press [OUTPUT] on the front panel or [VCR] on the remote control.
If you want to use the DVD player during a Timer Recording or while indicator on the front panel is on or blinking.
• Press [POWER] to turn on the unit. Press [DVD] on the remote control to choose DVD mode, then continue with the other
DVD features as described in this manual.
NOTE (for Timer Recording) :
• If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.
DVC841G_E8A04UD.indd 13 2006/02/08 18:36:07