Sylvania DVC841G DVD VCR Combo User Manual


 
EN
27
1
Turn on the TV and set it to channel 3.
If channel 3 has been already occupied for broadcasting,
see “RF Output Channel” section.
2
Select your language in the first time you turn on this unit.
Then press [B] to go to next step.
or
POWER
Quick Use Guide
Please refer to “Basic TV Connection” on the front page
before you use this unit.
RF Output Channel
If channel 3 has been already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press
[OUTPUT] on the unit so that the VCR OUTPUT
light is lit.
If noise appears on the TV screen, press [VCR/TV] on the
remote control.
4) Press [PLAY B] once.
5) After a few seconds, press and hold [PLAY B] on the
unit for 3 seconds.
• The RF output channel will change to channel 4 from
channel 3 and you will see a playback picture.
• When a picture does not appear on the TV screen,
repeat step 4.
6) Press [STOP C] to stop playback.
1
Connections
Clock Set Up
5
Turn On the Unit for the First Time
VCR/DVD Switching
4
3
Installing the Batteries for the Remote
Control
2
CHANNEL
OPEN/CLOSE
VCR DVD
PROGRESSIVE SCAN
SKIPH
STOP PLAY
G SKIP
REV FWD
OUTPUT
OUTPUT
DVDVCR
OUTPUT button
DVD OUTPUT
light
VCR OUTPUT light
DVD button
VCR button
POWER
DISPLAY VCR DVD PAUSE
SLOW
VCR/TV
SKIP/CH.
PLAY
STOP
REC/OTR
MENU
SETUP TOP MENU
MODE ZOOM
SUBTITLE
T-SET
ANGLE
ENTER
RETURN
SEARCH
MODE
REPEAT A-B
OPEN/CLOSE
/EJECT
SPEED AUDIO
CLEAR/
C. RESET
1 2 3
4 5 6
7 8 9
0
+10
VCR MODE
Press [VCR] on the remote control. (Verify that the VCR OUTPUT
light is lit.)
DVD MODE
Press [DVD] on the remote control. (Verify that the DVD OUTPUT
light is lit.)
No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using
[SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).
• If “AUTO SET UP” appears on the TV screen again, check the
cable connections. Then, press [B] once again.
Yes Press [MENU] to exit.
Do you connect the cable from the cable box or the satellite box to
the unit’s ANT-IN jack?
Hint
• Pressing only [OUTPUT] on the front panel DOES NOT switch the
mode of the remote control. You MUST select the correct mode on
the remote control.
1
Press [MENU] and select “CLOCK SET“.
Then press [B] to go to next step.
2
Select the current month.
Then press [B] to go to next step.
3
Select the current day.
Then press [B] to go to next step.
4
Select the current year.
Then press [B] to go to next step.
5
Select the current hour.
Then press [B] to go to next step.
6
Select the current minute.
Then press [B] to go to next step.
7
Select “AM” or “PM”.
8
To exit the CLOCK SET screen
• If the clock is not set, the CLOCK SET screen appears when
you press [MENU]. In this case, go to step 2.
or
MENU
or
or
or
or
or
or
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 2 0 0 6
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
3
Press [B] to start Auto Set Up.
CH 01
AUTO SET UP
NO
YES
VCR
VCR
2
1
3
2
1
3
2
1
3
2
3
1
DVC841G_E8A04UD.indd 27 2006/02/08 18:36:35