Filter
Top Products
Operation Guide
TC-14A12P / TC-20B12
- 6 -
ENGLISHENGLISH
ENGLISHENGLISH
ENGLISH
General OperationGeneral Operation
General OperationGeneral Operation
General Operation
Power Button (O stand by mode)Power Button (O stand by mode)
Power Button (O stand by mode)Power Button (O stand by mode)
Power Button (O stand by mode)
To turn the unit ON with this button, the power switch on the TV panel must
be ON. To turn it OFF, press the button again (stand by mode). If the unit
was turned OFF with the remote control (stand by mode), it is also possible
to turn it ON by pressing either channel button.
Note:Note:
Note:Note:
Note:
• Leaving the unit in the stand by mode will not cause any damages and
energy consumption is minimum.
• It is recommended to turn the unit OFF periodically by using the TV
power switch. When the unit is turned ON again after 30 minutes, the
demagnetization circuit of picture tube is activated.
• If the unit is to be left unused for a long period of time, turn it OFF by
using the TV power switch, disconnect the antenna and unplug the AC
power supply cord.
Channel ButtonsChannel Buttons
Channel ButtonsChannel Buttons
Channel Buttons
Press these buttons to select the
programmed channels.
1.1.
1.1.
1.
2.2.
2.2.
2.
3.3.
3.3.
3.
Channel Keyboard for Direct Selection (Memory Position)Channel Keyboard for Direct Selection (Memory Position)
Channel Keyboard for Direct Selection (Memory Position)Channel Keyboard for Direct Selection (Memory Position)
Channel Keyboard for Direct Selection (Memory Position)
Press these buttons to select the desired channel.
To select channels with two figures, press the -/-- button and then press the
buttons corresponding to the channel number.
Example: For channel 12, press -/-- , 1 , 2
To select channels with three figures, press the buttons corresponding to
the channel number.
Note:Note:
Note:Note:
Note:For selecting channels with three figures, the
CH SELECT CH SELECT
CH SELECT CH SELECT
CH SELECT
function must be in
DIRECTDIRECT
DIRECTDIRECT
DIRECT mode, and the
ANTENNA ANTENNA
ANTENNA ANTENNA
ANTENNA mode in
CABLECABLE
CABLECABLE
CABLE (Refer to Tuning Procedures - Channel Selection and
Antenna Mode).
11
11
1
88
88
8
33
33
3
1313
1313
13
66
66
6
55
55
5
22
22
2
44
44
4
99
99
9
1414
1414
14
1111
1111
11
77
77
7
1010
1010
10
1212
1212
12
CHANNEL
VV
VV
V
olume Buttons olume Buttons
olume Buttons olume Buttons
olume Buttons
(+, –)(+, –)
(+, –)(+, –)
(+, –)
Press these buttons to adjust
the listening level.
Time indication will flash
to indicate the last three
remaining minutes prior to
turn OFF.
Recall Button ( Recall Button (
Recall Button ( Recall Button (
Recall Button (
) )
) )
)
Press this button to review the selected system.
Press it again to disable this function.
Mute Button ( Mute Button (
Mute Button ( Mute Button (
Mute Button (
) )
) )
)
Press this button to quickly
reduce sound level. Press it
again to restore sound.
The mute indicator (red) will
be displayed.
TV/ATV/A
TV/ATV/A
TV/A
V ButtonV Button
V ButtonV Button
V Button
Press this button to select TV or video input.
Note:Note:
Note:Note:
Note:
A numerical and
graphic indication will
be displayed. The
numerical indication
ranges from zero (no
sound) to 63 (maximum
level).
Note:Note:
Note:Note:
Note:
• When AUTO is selected, the unit will turn OFF automatically (stand by mode) 5 minutes after the TV station
broadcast is finished.
• This function (AUTO) will not operate when the VCR (AV) mode is selected.
To cancel the TIMER (
), select “0” (zero) by pressing the TIMER button, or turn the unit OFF by using the power
switch on the TV panel.
TT
TT
T
imer Button ( imer Button (
imer Button ( imer Button (
imer Button (
) )
) )
)
This TV can be programmed to
turn OFF after a certain period
of time.
Press this button repeatedly for
automatic turn OFF after 30, 60
or 90 minutes, as desired.
4.4.
4.4.
4.
5.5.
5.5.
5.
6.6.
6.6.
6.
7.7.
7.7.
7.
8.8.
8.8.
8.