Filter
Top Products
3
SETUP BY ENTERING DEVICE CODE
( Note: If you do not touch any keys on your URC within 10
seconds during set-up, your URC will automatically abandon
the set-up process and revert to the last entered code. This
feature reduces accidental erasure of your codes)
SET UP FOR TV
1. Turn on your TV
2. Look up the brand name of your TV in the DEVICE CODE
LIST (See page 6-8).
3. Look up the 3-digit Device Code next to the brand name
of your equipment. If there is more than one code listed
for your brand, start from the first code with the
following instructions:
4. Hold down both POWER and MUTE keys on your
URC simultaneously until the STATUS INDICATOR lights up
and stays red (about 4 seconds).
5. Release the POWER and MUTE keys. The STATUS
indicator should still be lit. If not repeat step 4.
6. Press the TV DEVICE INDICATOR key once. The STATUS
INDICATOR and the DEVICE INDICATOR should now both
be RED.
7. Use the number keys on your URC to enter the 3-digit
Device Code. If you have entered a valid code, the
STATUS INDICATOR will blink once. If you have entered a
wrong code, the STATUS INDICATOR will blink twice.
8. Try the keys on your URC that correspond to similar keys
on your original remote control, especially those you use
most. (Note that the URC will abandon the set-up
procedure if you do not press any keys on the URC for
more than 10 seconds). If your TV works
on all or most of the keys on your URC, you have
entered a suitable Device Code. Go to step 11.
(Note: Your URC will only operate functions controlled by
your original remote nor are the supplied codes
guaranteed to operate all these functions)
9. If the Device Code does not work properly on your TV,
press the TV INDICATOR KEY once. The STATUS
INDICATOR will blink briefly, then turn RED. The TV
INDICATOR should still be RED. (If either of the indicators
switch off whilst you are still programming your URC,
you should start again from step 3.)
10.Repeat steps 7-9 with the other codes listed for your
brand of TV until your URC operates most or all of the
functions that correspond with the keys on your original
remote control.
11.Once you have found a suitable code, to store it, press
the TV INDICATOR key twice. The TV INDICATOR will blink
twice and then go out as will the STATUS INDICATOR.
12.If none of the TV codes listed for your brand of TV work
correctly, select the code that provides the best results.
Alternatively, try the Library Search method, which is
fully explained further on in these instructions.
SET UP FOR VCR AND SAT
Repeat the same set-up method for your VCR and SAT, but
remember to press the VCR or SAT DEVICE INDICATOR key,
and select the corresponding Device Code listing.
SET UP FOR AUX KEY
The following instructions describe how to configure the AUX
key to act as a 2nd TV/VCR/SAT control.
13.First use the TV/VCR/SAT set-up method to find the
best code for the device you wish to program into the
AUX key following steps 1-11.
14.Wait until all indicator lights have gone out then hold
down the POWER and MUTE keys together on
your URC, until the STATUS INDICATOR lights up and
stays red. [About 4 seconds]
15.Release the POWER and MUTE keys. The STATUS
indicator should still be lit. If not repeat step 14.
16.Press the AUX DEVICE INDICATOR key once.
(AUX INDICATOR should turn RED)
17.Press briefly the TV or VCR or SAT DEVICE INDICATOR
corresponding to the type of device you are
programming into the AUX key.
18.Type in the 3 digit code that you found in step 13.
19.Press the AUX key twice to store your code. If you have
followed the set-up instructions correctly, the SATUS
INDICATOR and DEVICE INDICATOR will turn
off. Set up is now complete.
SET-UP BY LIBRARY SEARCH
If you cannot identify a suitable Device Code for your
equipment from the Device Code List, you may try our
library search method. (For many lesser known brands
codes may be present but not listed under that brand.)
During the search the selected DEVICE INDICATOR will flash
at various speeds. The entire search procedure may take
several minutes to complete. The following instructions uses
your television as an example for set-up using the Library
Search method.
TV SETUP BY LIBRARY SEARCH
1. Turn on your TV
2. Hold down both POWER and MUTE keys on your
URC simultaneously until the STATUS INDICATOR lights up
and stays red (about 4 seconds).
3. Release the POWER and MUTE keys The STATUS
INDICATOR should still be lit. If not repeat step 2.
4. Press the TV DEVICE INDICATOR key once. The STATUS
INDICATOR and the DEVICE INDICATOR should now both
be RED.
5. To search, aim your URC at your TV.
Steps
4. & 14.
Figure 1.
STATUS INDICATOR
DEVICE INDICATOR
KEYS
Figure 2.
Figure 3.
Step 7.
Step 6.
Step 16.
Steps
2. & 10.
Figure 4.
STATUS INDICATOR
DEVICE INDICATOR
KEYS
Figure 2.
Step 4.
Step 11.