Filter
Top Products
4
6. Press the POWER key repeatedly for 2 seconds ON and
two seconds OFF, until your TV goes into standby mode
(i.e. the TV switches OFF). Then continue with step 7.
If the TV INDICATOR key flashes twice and then goes out
before your TV goes into stanby mode you have reached
the end of the library. Return to step 2 and repeat
library search one more time.
7. Try the number keypad to see if your device switches ON
again and the keys work correctly. If your device does
not switch ON, press the Mute key and then the
Power key to repeat the code so that the Device
comes ON. Now try the number keypad. (NOTE: If you
accidentally skipped a code that turned your TV ON or
OFF, you can return to the skipped code by pressing the
Mute key.)
8. If the code you have found does not work correctly,
make sure that the TV INDICATOR and STATUS
INDICATOR are still red, before you repeat steps 6 and 7
until you find a better code. If the indicator lights have
gone out, repeat the set-up procedure from step 2.
9. Once you are happy with the code found, press the TV
INDICATOR key once to store the code. The STATUS
INDICATOR and DEVICE INDICATOR will turn off and
set-up is complete.
VCR & SAT SETUP BY LIBRARY SEARCH
Simply repeat the above procedure to search for the Device
Codes for your VCR and SAT but instead of the TV DEVICE
INDICATOR key press either the VCR or SAT DEVICE
INDICATOR key in step 4
AUX SETUP BY LIBRARY SEARCH
10.Follow steps 2 and 3 in TV SETUP BY LIBRARY SEARCH.
11.Press the AUX DEVICE INDICATOR key once. (AUX
INDICATOR should turn RED)
12.
To set up a TV on the AUX DEVICE KEY follow steps 4 to 8.
13.Once you are happy with the code found, press the AUX
INDICATOR key once to store the code. The STATUS
INDICATOR and DEVICE INDICATOR will turn off and set-
up is complete. Your TV will now work when the AUX key
is selected.
To operate a VCR or SAT using the AUX key, follow steps 10
to 13 as for TV but instead of the TV DEVICE INDICATOR key
press either the VCR or SAT DEVICE INDICATOR key in step 10
OPERATING YOUR URC
Once you have set up your URC, it should operate similarly
to your original remote control and perform most or all of
the main functions. To operate, just aim it at your equip-
ment, press the appropriate DEVICE INDICATOR key and
press the required function key. The DEVICE INDICATOR
flashes during signal transmission to confirm that a function
key is in operation.
Please Note: The URC can only duplicate functions that are
on your original remote control. Any extra keys on the URC
which are not on the original will not function.
SHIFT Functions
To operate a secondary function, press SHIFT followed by the
corresponding function key. The SHIFT key remains func-
tional for as long as any other key is operated, or until 5
seconds have elapsed after the last key pressed. When the
SHIFT key is operated, the STATUS INDICATOR lights up
green and the DEVICE INDICATOR red while the SHIFT key is
pressed down. The STATUS INDICATOR then stays ON for
another 5 seconds. The SHIFT key can be cancelled before
the 5 seconds time-out period by pressing the SHIFT key
again.
MAINTENANCE
1. Do not expose your URC to dust, strong sunlight,
humidity, high temperature or mechanical shock.
2. Do not use old and new batteries together as old
batteries tend to leak.
3. Do not use corrosive or abrasive cleansers on your URC.
4. Keep the unit dust free by wiping it with a soft, dry cloth.
5. Do not disassemble your URC, it contains no user
serviceable parts.
FREQUENTLY ASKED QUESTIONS
Q. I am unable to program or operate my URC, but the
indicator lights on my URC operate correctly.
A. Check your A/V device. If the device’s mains switch
is turned off, your URC can not operate your device.
A. Check if the batteries are low and replace the batteries.
A. If several Device Codes are listed under the brand
name of your A/V device, try each code one by one
until most or all of the keys work correctly.
Q. The STATUS INDICATOR light does not stay ON when
entering set up mode.
A. Make sure both the POWER and MUTE buttons are
pressed simultaneously
Q. My A/V equipment responds only to some commands.
A. You may have selected a code for which only some
commands work correctly. Try the other codes listed
for your brand.
A. Try the Library Search if you are still unsuccessful.
Q. Some of my equipment will not work with any of the
codes listed.
A. Make sure that you have selected the correct device
listing
A. Try the Library Search function as some more recent
Disclaimer: Whilst we have tried to supply a comprehensive
library of codes we cannot guarantee that your URC will be
fully compatible with all equipment. Some brands, models or
functions may not be available in the code library due to
differences in operation to your original remote or where
the code has not yet been added to the library.
The manufacturer cannot accept any liabilities resulting from
incorrect use of this product.
SPECIFICATIONS
Operating system:- Pre-programmed infra-red remote con-
trol system.
Compatibility:- Operates most brands of infra-red remote
controlled TV’s, VCRs, Sat.’s.
Power requirement:- 2 x AAA-size alkaline batteries.
Effective range:- 7.65M (25 feet), +/- 25 degrees.
Alkaline battery life:- Normal operation 6 months.
Dimensions:- 199 (L) x 56 (W) x 24 (H) mm.
Weight without batteries:- 105g
LOW BATTERY LEVEL
If the indicator flashes twice slowly after pressing a key func-
tion, the battery level is low & you must fit new batteries. If
the batteries are removed, your URC will retain its memory
for approximately 10 minutes only.
Customer Care Line–Tel: 08457 573 479 (UK only)
Technical Support Web Site: http://technical.philex.com
Technical Web Site Enquiries: technical@philex.com