Filter
Top Products
OTR (One Touch Recording)
This function enables you to set a recording length simply by
pressing RECORD on the DVD/VCR.
1 Follow steps 1 to 2 in “Recording without automatic switch-
off” section.
2 Press RECORD on the DVD/VCR repeatedly until the desired
recording length appears.
0:00 0:30 1:00.... 7:30 8:00
REC (Normal recording)
• Recording stops when 0:00 is reached.
To check time remaining during an OTR
Press DISPLAY.
To change the recording length during an OTR
Press RECORD until the desired length appears.
To stop an OTR before recording is finished
Press STOP.
To cancel the OTR but continue recording
Press RECORD repeatedly until “REC” appears in the upper
left corner of the TV screen.
General information
Use a TIMER programming to automatically start and stop a
recording at a later time or date.The DVD/VCR will switch to
the right programme number and begin recording at the cor-
rect time.With this DVD/VCR, you can pre-programme up to
eight recordings within a period of one year.To make a pro-
grammed recording,your DVD/VCR needs to know:
* the date you want to make the recording
* the programme number of the TV channel
* the start and stop time of the recording
* VPS or PDC on or off
This information is saved in a TIMER block.
12
English
What is 'VPS/PDC'?
'VPS' (Video Programming System)/ 'PDC' (Programme Delivery
Control) are used to control the start and duration of TV channel
recordings.If a TV programme starts earlier or ends later than
scheduled,the DVD/VCR will turn on and off at the correct time.
What do I need to know about 'VPS/PDC'?
Usually the VPS or PDC time is the same than the start time.But
if your TV guide shows a VPS or PDC time which is different from
the programme’s scheduled start time,e.g.20.10 (VPS/PDC
20.14),you must enter the VPS/PDC time exact to the minute.If
you want a start time different from the VPS/PDC time,you must
switch VPS/PDC off.
Programming a recording (with the
'SHOWVIEW® system')
You no longer need to tediously enter the date, programme
number,start and end time.All the information needed for pro-
gramming is contained in the SHOWVIEW-programming number.
You can find this SHOWVIEW number in most TV listing maga-
zines written next to the concerned programme.
1 Press SV/V+.
2 Enter the entire SHOWVIEW num-
ber.This number is up to 9 digits
long and can be found next to the
start time of the TV programme in
your TV listing magazine. [e.g: 1-
234-5 or 1 234 5]
If you make a mistake, you can
clear your input with CLEAR.
3 Press SV/V+.
4 Select ONCE,DAILY,or WEEKLY
recording with K/L.Then press B.
R
ShowView system
ShowView No.
12345
– – – –
SET=SV/V+
CORRECT=CLEAR
END=EXIT
ShowView system
→ONCE
DAILY
WEEKLY
SELECT
KL CHOOSE B
END=EXIT
Selecting once/daily/weekly recordings
Using K/L, select from the following options:
'ONCE': Recording once
'DAILY': Repeated daily recordings (Monday to Friday)
'WEEKLY.':Repeated weekly recordings (every week on the same
day)
'- -' appears at PROG..
* The programme number of the TV channel has not yet been
assigned to the S
HOWVIEW number.Using the numerical key
pads,select the corresponding programme number (name) of
the TV channel.
The following message appears on the screen:'ERROR'
* The entered SHOWVIEW number is incorrect.Correct your input
or end with STATUS/EXIT.
* Check the time/date (see chapter 'Installing your video',section
'Setting the time and date').
* A daily recording was entered for the wrong day.Daily pro-
gramming can only be used for recordings to be made from
Monday to Friday.
The following message appears on the screen:'TIMER
NOT COMPLETED'
* The channel is wrong.
5 The decoded data appears after confirmation.You can go back
to change the data.Select the corresponding input field using
B or CLEAR.Change the data with numerical key pad.
6 When all inputs are correct, press STATUS/EXIT.The program-
ming information is stored in a Timer block.
7 Insert a cassette with an intact security tab (unprotected).
8 Press TIMER SET.
'RECORD TIMER' will light up on the DVD/VCR display.
Switching on 'VPS/PDC' in the 'START' input field
Select 'VPS/PDC' using B or CLEAR.Press '1' to switch off
'VPS/PDC' or press '2' to switch on 'VPS/PDC'.
Programming a recording (without the
SHOWVIEW® system)
1 Press VCR,then DISC/VCR MENU.
2 Select 'TIMER' with K/L.Then
press B.
3 Select ONCE,DAILY,or WEEKLY
recording with K/L.Then press B.
If all Timer blocks are in use,‘FULL’
will appear on the OSD.
4 Select the desired Timer block with
numerical key pads.(The flashing
number indicates an empty TIMER block.)
5 Enter the Start time (START) End time (STOP),Programme
number (PROG.),VPS/PDC information and the Date with
numerical key pads.
6 When all inputs are correct, press STATUS/EXIT.The program-
ming information is stored in a TIMER block.
7 Insert a cassette with an intact security tab (unprotected).
8 Press TIMER SET.
Selecting once/daily/weekly recordings
Using K/L, select from the following options:
'ONCE': Recording once
'DAILY': Repeated daily recordings (Monday to Friday)
'WEEKLY.':Repeated weekly recordings (every week on the same
day)
Programme numbers of the ' AV1 ' , ' AV2 ' and ' AV3'
scart socket
You can also programme recordings from external sources via
scart socket AV1(TV),AV2 (DECODER) or AV3(FRONT).
SELECT KL CHOOSE B
→ONCE
DAILY
WEEKLY
TIMER LIST
END=EXIT
Programming a Recording (TIMER)