Filter
Top Products
4
EN
Important for the United Kingdom
This apparatus is fitted with an approved moulded 10
Amp plug.To change a fuse in this type of plug pro-
ceed as follows:
1.
1.Remove fuse cover and fuse.
2.
2.Fix new fuse which should be a
BS1362 3A,ASTA or BSI approved type.
3.
3.Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fitted in its
place.
If the mains plug contains a fuse, this should have a
value of 3A. If a plug without a fuse is used, the fuse at
t
he distribution board should not be greater than 3A.
How to connect a plug:
The wires in the mains lead are coloured in accor-
dance with the following code:
BLUE- 'NEUTRAL' ('N')
BROWN- 'LIVE' ('L')
4.
4.The BLUE wire must be connected to the terminal
which is marked with the letter 'N' or coloured
BLACK.
5.
5.The BROWN wire must be connected to the termi-
nal which is marked with the letter 'L' or coloured
RED.
6.
6.Do not connect either wires to the earth terminal in
the plug which is marked with the letter 'E' or by
the safety earth symbol
or coloured green or
green-and-yellow.
Before replacing the plug cover, make certain that the
cord grip is clamped over the sheath of the lead-not
imply over the two wires.
Preparing the remote control for
operation
The remote control and its batteries are packed
separately in the original video recorder packaging.
You must install the batteries in the remote control
before use.
1.
1.Take the remote control and the enclosed batter-
ies (2 batteries).
2.
2.Open the remote control's battery compartment
and place the batteries in it as shown in the pic-
ture and close the battery compartment.
The remote control is now ready to use.Its range is
approximately 5 metres.
Connecting your video recorder to
the TV set
The necessary cable connections must be made
before you can record or play-
back TV programmes using
your video recorder.
We recommend that you use a
scart cable to connect your TV
and video recorder.
Connecting with a scart cable
Have the following cables ready:
an aerial cable (1, sup-
plied), a scart cable (2, not
supplied).
1.
1.Remove the aerial
cable plug from your TV
set. Insert it into the
AERIAL at the back of
the video recorder.
2.
2.Insert one end of the
supplied aerial cable
into the RF OUT at the
back of the video
recorder and the other
end into the aerial input
socket at the back of
the TV set.
3.
3.Plug one end of a scart
cable into the scart
socket ‘TV’ at the back
of the video recorder
and the other end into
the suitable scart sock-
et on your TV reserved
for the video recorder
operation (see your
TV's operating instructions).
4.
4.Switch on the TV.
5.
5.Insert AC cable into the wall socket
3. Connecting the video recorder
What is a scart cable?
The scart or Euro AV cable serves as the universal
connector for picture, sound and control signals.With
this type of connection, there is practically no loss of
quality during the picture or sound transfer.
AERIAL
RF OUT
R
)
TV
AERIAL
RF OUT
RF OUT
T
V
AERIAL
TV
R
F O
U
T
TV
A
ER
IAL
12
My TV has several scart sockets.Which one
should I use?
Select that scart socket which is suited for the
video output as well as for the video input.
My TV has a configuration menu for the scart
socket.
Please configure this scart socket as Input-Output.
The severed plug must be destroyed to avoid a possi-
ble shock hazard should it be inserted into a 13A
socket elsewhere.
HE271BD(EN).QX3 03.2.21 2:25 PM Page 4