Filter
Top Products
12
Note: This modulator frequency might already be oc-
cupied by another TV station in your reception area. In
this case you will find that the picture quality on your TV
set will be poor when receiving one or more TV
channels.
* Adjusting the modulator frequency: If the picture
quality only deteriorates when the video recorder is
switched on, adjust the modulator frequency. The fre-
quency can be adjusted at step 2with the
P r
or the
P q
button. Confirm the adjusted frequency with the
OK
button.
* Switching off the modulator: If you cannot eliminate
picture or sound interference using the above method
you can switch off the built-in modulator. You should
only do this if you have connected the video recorder to
the TV set using a scart cable. ’Playback via the aerial
cable’ is not possible when the modulator is switched
off.
At step 2, press the
CLEAR (CL)
button for several sec-
onds until ’MOFF’ (modulator switched off) appears in
the display. You can switch back again in the same way.
* The GK switch:
If you don’t have sound during playback, switch to the
other TV system on the video recorder. At step 2,
select between e.g.: ’K591’ (TV system SECAM-D,K) and
e.g.: ’G591’ (TV system PAL-B,G) with the
SELECT
but-
ton.
Before you call an engineer
If, contrary to expectation, you experience any difficulty in
operating this video recorder, it may be caused by one of the
reasons mentioned below. You can also call the customer
service in your country.
You will find the telephone numbers in the enclosed guar-
antee leaflet.
The set does not respond to any button being pressed:
• No power supply.
• A programmed recording is currently being made.
• Technical disturbance: disconnect from the mains for 30 sec-
onds, then re-connect. If this does not have any effect, you can:
1. Disconnect from mains. 2. Re-connect to mains whilst
holding down the
STANDBY m
button on the video recorder.
All stored data will be reset (cleared).
Cassette jammed:
• Don’t use force. Pull out the mains plug for a moment.
Remote control does not operate:
• Remote control not pointed toward the video recorder.
• Batteries are exhausted.
No playback from video recorder:
• No recording on the cassette.
• The VCR programme number on the TV set was incorrectly
selected or incorrectly set.
• The connecting cable between the TV set and the video
recorder has come loose.
Poor playback from video recorder:
• TV set not properly adjusted.
• Cassette badly worn or of poor quality.
• Read the section about ’How to eliminate picture disturbance’ in
chapter ’PLAYBACK’.
No recording possible:
• TV channel not stored or wrongly selected.
• Cassette with erase protection has been loaded.
Programmed recording does not function:
• TIMER not set properly.
• Time/date wrongly programmed.
• A cassette with erase protection has been loaded.
• ’VPS’ switched on but ’VPS time’ wrong. Check aerial.
Picture or sound interference on TV reception :
• Turn to Chapter 4 ’SPECIAL FEATURES’ and read in the section
’Playback via the aerial cable’ the note ’Adjusting the modulator
frequency’ as well as the note ’Switching off the modulator’.
• Have your aerial checked.
No sound playback:
• Turn to Chapter 4 ’Special Features’ and read in the section
’Playback via the aerial cable’ the note ’GK-switch’.
Enter the serial number of your appliance here:
MODEL NO./TYPE VR 675CG
PROD.NO.:/SER.NR. .....
This product complies with the requirements of the Directive
73/23/EEC + 89/336/EEC + 93/68/EEC.
3103 166 20921
8131/001
(WwnnNNNwwnwNNnwnWwnNnNwWnNwnnW)
VR 675CG