Filter
Top Products
18
EN
7.
7.When all inputs are correct, press .
The programming information is stored in a
Timer block.
8.
8.Insert a cassette with an intact security tab
(unprotected).
9.
9.Switch off with .The pro-
grammed recording will only function when
the video recorder is switched off with
.
Programming a recording
(without the VIDEO Plus
+
system)
1.
1.Switch the TV on. If applicable, select the pro-
gramme number for the video recorder opera-
tion.
2.
2.Press .The main menu will appear.
3.
3.Select 'TIMER' with or .
Then press .
4.
4.Select 'ONCE', 'DAILY' or 'WEEKLY' recording
with or . Then press
.
5.
5.Select the desired Timer block with .
6.
6.Enter the Start time (START), End time
(STOP), Programme number (PROG.), PDC
information and the Date (DATE) with .
7.
7.When all inputs are correct, press
. The programming information
is stored in a TIMER block.
8.
8.Insert a cassette with an intact security tab
(unprotected).
9.
9.Switch off with .
The programmed recording will only function
when the video recorder is switched off with
.
STANDBY/ON
yy
STANDBY/ON
yy
STATUS/EXIT
0..9
0..9
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
MENU
STANDBY/ON
yy
STANDBY/ON
yy
STATUS/EXIT
SELECT KL CHOOSE B
→ONCE
DAILY
WEEKLY
TIMER LIST
END=EXIT
Programme numbers of the 'AV1', 'AV2' scart
socket and 'AV3' (FRONT A/V CONNECTORS)
You can also programme recordings from exter-
nal sources via scart socket AV1(TV), AV2
(DECODER) or AV3 (FRONT A/V CONNEC-
TORS). Select programme number 'AV1' with
0.0.1, 'AV2' with 0.0.2 or 'AV3' with 0.0.3.
'- -' appears at PROG. .
• The programme number of the TV channel
has not yet been assigned to the PlusCode
programming number. Using the number but-
tons on the remote control, select the
corresponding programme number (name) of
the TV channel.
The following message appears on the
screen: 'ERROR'
• The entered PlusCode programming number
is incorrect. Correct your input or end with
.
• Check the time/date (see chapter 'Installing
your video', section 'Setting the clock').
•A daily recording was entered for the wrong
day. Daily programming can only be used for
recordings to be made from Monday to Friday.
Switching on 'PDC'
• Select 'PDC' using .
Press '1' to switch off 'PDC' or press '2' to
switch on 'PDC'.
CLEAR
FWD 1- B
STATUS/EXIT
0..9
Selecting ONCE/DAILY/WEEKLY recordings
'ONCE': Recording once
'DAILY': Repeated daily recordings
(Monday to Friday)
'WEEKLY': Repeated weekly recordings
(every week on the same day)
Error message: 'FULL'
• If this error message appears after you select
'ONCE', 'DAILY' or 'WEEKLY' on TIMER menu
and press
,
then all TIMER blocks
are already programmed. No more recordings
can be programmed. If you want to clear or
check a programmed recording (TIMER block),
select the programme number on TIMER LIST
menu and press .
CLEAR
FWD 1- B
The following message appears on the
screen: 'TIMER NOT COMPLETED'
• The channel is wrong.
HG491/495BD(EN).qx3 03.12.19 9:54 PM Page 18