Filter
Top Products
7
RS-232C Adjustment Mode
1.5 List of RS-232C Commands
How to read this Table
• RS-232C adjustment validity : Indicates whether the RS-232C adjustment mode can be used
• Normal validity : Indicates whether the normal-operation mode can be used
• Numerical direct validity : With a 3-digit number attached to the end of a command, the
command directly sets that adjustment value
•
‡ or ¶: Valid, No mark: Invalid
(NOTE)
¶ values are not stored in the last memory.
Command name AJY (232C integrator) Display
RS-232C
Adjustment
Validity
Normal
Validity
Numerical
Direct
Validity
[A]
AJN – Terminates the 232C integrator adjustment mode. ¶
AJY ADJUST: ON Starts the 232C integrator adjustment mode. ¶
AMN AUDIO MUTING: OFF Turns OFF the audio mute. ¶¶
AMY AUDIO MUTING: ON Turns ON the audio mute. ¶¶
AST AUTO SET UP Executes AUTO SETUP. ‡
[B]
BHI B HIGH: ∗∗∗ Adjusts B. HIGH. ‡‡
BLW B LOW: ∗∗∗ Adjusts B. LOW. ‡‡
BRA BAUD RATE: #####-232C Displays the current baud rate. ¶
BRAS01 BAUD RATE: 1200-232C Sets the UART setting to 232C (1200BPS). ‡
BRAS02 BAUD RATE: 2400-232C Sets the UART setting to 232C (2400BPS). ‡
BRAS03 BAUD RATE: 4800-232C Sets the UART setting to 232C (4800BPS). ‡
BRAS04 BAUD RATE: 9600-232C Sets the UART setting to 232C (9600BPS). ‡
BRAS05 BAUD RATE: 19200-232C Sets the UART setting to 232C (19200BPS). ‡
BRAS06 BAUD RATE: 38400-232C Sets the UART setting to 232C (38400BPS). ‡
BRT BRIGHTNESS: ∗∗∗ Adjusts the brightness. ‡‡
BSL B SIDE MASK LEVEL: ∗∗∗ Adjusts the BLUE side mask. ‡‡
[C]
CFR CLOCK: ∗∗∗ Adjusts the CLOCK (PLL frequency). ‡‡
CGB COLOR DETAIL BLUE: ∗∗∗ Adjusts color detail BLUE. ‡‡
CGC COLOR DETAIL CYAN: ∗∗∗ Adjusts color detail CIAN. ‡‡
CGG COLOR DETAIL GREEN: ∗∗∗ Adjusts color detail GREEN. ‡‡
CGM COLOR DETAIL MAGENTA: ∗∗∗ Adjusts color detail MAGENTA. ‡‡
CGR COLOR DETAIL RED: ∗∗∗ Adjusts color detail RED. ‡‡
CGY COLOR DETAIL YELLOW: ∗∗∗ Adjusts color detail YELLOW. ‡‡
CLS COLOR SYSTEM: ##### Displays the current color system. ¶
CLSS01 COLOR SYSTEM: AUTO Sets the color system to AUTO. ‡
CLSS02 COLOR SYSTEM: NTSC Sets the color system to NTSC. ‡
CLSS03 COLOR SYSTEM: PAL Sets the color system to PAL. ‡
CLSS04 COLOR SYSTEM: SECAM Sets the color system to SECAM. ‡
CLSS05 COLOR SYSTEM: 4.43NTSC Sets the color system to 4.43NTSC ‡
CLSS06 COLOR SYSTEM: PAL M Sets the color system to PAL M. ‡
CLSS07 COLOR SYSTEM: PAL N Sets the color system to PAL N. ‡
CM1 COLOR MODE: NORMAL Sets the color mode to NORMAL. ‡‡
CM2 COLOR MODE: STUDIO Sets the color mode to STUDIO. ‡‡
CNT CONTRAST: ∗∗∗ Adjusts the CONTRAST. ‡‡
COF COLOR OFF: ∗∗∗∗∗∗∗∗ Displays the current COLOR OFF setting. ¶
COFS00 COLOR OFF: DISABLE Disables COLOR OFF. ‡
COFS01 COLOR OFF: ENABLE Enables COLOR OFF. ‡
COL COLOR: ∗∗∗ Adjusts the COLOR. ‡‡
CPH PHASE: ∗∗∗ Adjusts the PHASE (PLL phase). ‡‡
CTP COLOR TEMP.: ∗∗∗∗∗∗∗∗ Displays the current COLOR TEMP. ¶
CTPS01 COLOR TEMP.: LOW Sets the COLOR TEMP. to LOW. ‡
CTPS02 COLOR TEMP.: MID LOW Sets the COLOR TEMP. to MID LOW. ‡
CTPS03 COLOR TEMP.: MIDDLE Sets the COLOR TEMP. to MIDDLE. ‡
CTPS04 COLOR TEMP.: MID HIGH Sets the COLOR TEMP. to MID HIGH. ‡
CTPS05 COLOR TEMP.: HIGH Sets the COLOR TEMP. to HIGH. ‡
Remarks