Filter
Top Products
To cop)' (dub) tapes, connect the two VCR's as shown
below. Use shielded audio/video cables (such as RCA
-,-AH00,. gAH005, or .=AH036).
The connections from the recording VCR to your TV are
the ones you normally use. It's best to play the original
tape on the same machine that was used to record it (so
you don't have to adjust the TRACKING buttons.)
Coaxial Antenna Cable=
(such as RCA =AH037)
If you have a "IV Monitor/Receiver
iCAUTION: The unauthorized recording of television
programs and other materials may infringe the rights
of others.
V YHF _,-
.,.beok OR i if°
.
Audio/Video Cables* _=__)
(such as RCA AH002 or AHO05)
el with Audio/Video inputs, you F__ ---------- -- - _ ..
lad _ _ can also connect these jacks to i _, (
I produce a slightly better picture "_'/ -
-_ dur,ngplayback. [ ], Rec.ordlr_VCR '_" _.F _ _;
•_ I I (Connect'this VCR tO {_)) / _/
IIIllmlw :
Optional / m__mmmm_mm J
Audio/Video Cebles"
(such as RCA AH002 or AH005) *Optional accessory a_,ailable from your RC.A dealer,
Simplified Operating Instructions to Dub Tapes
I. Connect the two VCR's as shown above. (Use
shielded audio/video cables such as RCA
#.AHO02, -=AH005. or _AH036.)
2. Turn on TV.
3. Tune TV to VCR Channel ,,channel 3 or 4}.
4. Turn on both VCR's.
5. Insert recorded cassette into Playback VCR.
6. Insert blank cassette into Recording VCR.
7. Press TV VCR button on remote control of
Recording VCR so _ indicator is on, CThis
allows you to watch the recording while it's in
progress.)
Note: If you want to watch another TV channel
on the "IV '_,hile you're dubbing the tape. hrst
press the TV t.'C,R button on remote control so
the _ indicator is out and then use the TV's
channel selecto: to select the channel you want
to watch on the TV.
8. Select channel _i or the Recording VCR. The
:.,adicator wilt appear m the display.
(Press CHANNEL • or • button if channel 91
is programmed in the VCR's Channel Memory
or press "9" then "'1" on the remote control.)
Note: If the Recording ¥CR has a TUNER/
LINE switch, place it m the LINE position.
9. Select the desired tape speed on the Recording
VCR (SP, LP or SLP).
10. Rewind cassettes to the beginning if necessary.
1l. Place the Recording VCR into the record mode.
12. Press PLA }"on the Playback VCR to start
playing the prerecorded cassette.
t3. Adjust TRACKING buttons on Playback VCR if
necessary.
Note: If the prerecorded cassette is not being
played on the same VCR that ori0nally
recorded it. streaks may appear in the TV
picture. Simply press the TRACKtNG • or •
button on the Playback VCR to eliminate the
streaks.
14.
If you want to edit out unwanted material, press
PAUSE on the Recording VCR while tt is
recording. Press PAUSE again to resume
recording.
Note: Use the PAUSE button only for brief
pauses. If you want to pause for more than three
or four rrunutes stop the VCR by pressing
STOP. When you are read)' to resume, place the
VCR back rote the record mode.
t5. The "IV does not have to be turned on to dub a
tape. You may turn off the TV if desired after
the recording has started.
16. Stop both VCR's when the recording is finished.
30