Filter
Top Products
1. What channel do I put my television on to watch a DVD
player?
To determine where the DVD player is connected, turn the DVD
player and TV on and set the TV on channel 3. Then press the
INPUT key on the remote control to scroll through the signal
inputs to locate the DVD player startup screen.
2. I am not receiving all of my VHF and UHF channels or cable
channels?
Make sure an antenna or your cable service is connected to
the ANT. Terminal. If there is a VCR connected, make sure it is
turned off. Press the RESET key on the remote two times to
begin an automatic channel search.
3. I connected a satellite receiver directly to the digital con-
nection on the television and cannot receive my satellite
channels?
Although the satellite signal is digital, it still must be processed
by a satellite receiver. The “Out to TV” connection on the
satellite receiver must be connected to the ANT. Terminal on
the television.
4. How do you turn the caption on and off?
To turn captioning on or off, press and release the CAPTION
key on the remote until the desired caption mode appears (CC1
and Digital CC1 are used most commonly).
5. I’m connected to a satellite system. How do I get my
television to go to channel 73?
Turn on the satellite receiver then press the RESET key on the
remote twice to begin a channel search. If after the search no
satellite channels appear. Press the MENU key on the remote
and select “Analog Antenna Signal.” Use the CURSOR keys
to select CABLE. Press the EXIT key, then press in channel 73.
6. How do I get a full picture on the screen?
If you are connected to a Cable box or Satellite receiver, bring
up the box menus and select 4:3 as the screen aspect ratio.
Then press the PIX SHAPE key on the television remote
control for the desired screen shape.
7. Is my remote universal?
No, this remote control is designed to operate a Sanyo
television only.
8. When I do a channel search some of my digital channels
disappear. What is wrong?
Many digital stations are not on-the-air 24 hours a day. After
doing the initial channel search, always use the menu system
to perform a “Digital Add-on Search” to add new digital chan-
nels, so that stations not on-the-air during the search will not
be erased.
9. There is no picture, sound is ok?
Check appropriate video connection to make sure it corre-
sponds to the audio connection being used. If the sound is
associated with component jacks on a DVD player, it may be
necessary to access the DVD menu to select the component
outputs or S-Video output.
10. There is no sound, picture is clear?
If you are connecting your television through the Composite
jacks (Video1), S-Video jack (Video1), or Component jacks
(Video2 or Video3) the matching audio jacks must also be
connected.
11. The picture is not as clear as it should be. Am I using the
best quality connection?
Picture quality is classified as follows:
Analog RF cable connection . . . . . . . . . . . . . . . . . . . . . Basic
Video1 (Composite – yellow) . . . . . . . . . . . . . . . . . . . . . Good
Video1 (S-Video). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Better
Video2 (Component – green, blue, red) . . . . . . Exceptional
Video3 (Component – green, blue, red) . . . . . . Exceptional
Digital Antenna In. . . . . . . . . . . . . . . . . . . . . . . . . Exceptional
12. How do I register my television warranty?
No registration is necessary, just hold on to your sales receipt.
We will warranty the television from the date on the receipt.
13. Where is the code for a Sanyo television to program into
my universal remote?
You must obtain the code from the manufacturer of the remote
control you want to program. Refer to the remote’s owner’s
manual.
14. When I adjust the volume on the television why does the
volume level on the surround sound system remain steady?
The audio output jacks are set to a fixed level and do not vary
with the television volume. The volume control on the surround
sound system must be used.
15.My digital channel number doesn’t match the station
number.
On some digital channels the channel number displayed on the
television will be different than the channel ID number. This is
determined by the digital package broadcasted from the local
station through the digital signal.
16. What is the recommended method for cleaning the cabinet
and screen?
Clean the cabinet with a soft-dry
cloth. Clean the screen using a
damp-soft-cotton cloth.
45
FREQUENTLY ASKED QUESTIONS (FAQ)