Filter
Top Products
8
FirstFirst
Please connect all signalsPlease connect all signals
and antennas to jacks andand antennas to jacks and
the terminals on the back.the terminals on the back.
Then press CHannel UP key.Then press CHannel UP key.
When the television is powered on for the first time,
it automatically checks for the presence of Digital and
Analog RF signals.
•
Press the POWER key to turn on the TV.
•
Then press the CHANNEL UP key to automati-
cally search for available channels: Digital
(ATSC) and Analog (NTSC).
If an analog channel was found, the TV will
start Auto Clock Setting (see step 5).
NOTES: Channel information found during channel search is
stored in two Channel Scan Memory databases
(Analog and Digital). After channel search is completed,
the TV will tune to the lowest Digital channel or lowest
Analog channel if no digital channels are found.
If the TV does not detect any digital or analog channels,
a message advising the viewer to check the cables and
antenna connections will appear. In this case, you must
press
the CHANNEL UP key again to repeat the
channel search process. If after two searches the TV still
fails to detect any channels, the TV will tune to analog
channel 3. These two channel searches are required
even if you plan to use the TV only as a monitor.
If no analog or digital channels are found after the
second search, Channel Search will default to off-air
analog channels 2 through 69 and digital channel D3-1.
Select analog channels using the remote control
keypad. See page 14, item number 2.
4
CHANNEL SEARCH (REQUIRED SET-UP)
IMPORTANT NOTE: Spent or dis-
charged batteries must be recycled or
disposed of properly in compliance
with all applicable laws. For detailed
information, contact your local County
Solid Waste Authority.
2
INSTALL BATTERIES
•
Install two “AAA” Batteries (not included) so that the
“+” and “–” marks on the batteries match the “+” and
“–” marks inside the Remote.
To review the remote control functions, go to pages 14~15.
1
4
5
6
7
8
0
9
2
3
IN
P
U
T
IN
F
O
R
E
C
A
L
L
M
E
N
U
C
A
P
T
IO
NE
X
I
T
V
O
L
E
N
T
E
R
T
U
N
E
R
M
U
T
E
S
L
E
E
P
1
4
5
6
7
8
0
9
2
3
IN
P
U
T
IN
F
O
R
E
C
A
L
L
M
E
N
U
C
A
P
T
IO
N
E
X
I
T
V
O
L
E
N
T
E
R
T
U
N
E
R
M
U
T
E
S
L
E
E
P
CH
POWER
3
CONNECT AC POWER CORD
•
Connect AC Power Cord (supplied) to the Plasma TV
and electrical outlet as shown here.
The AC outlet must be near this equipment and must be
easily accessible.
To POWER CORD
CONNECTOR on back
of Plasma TV.
To 120 V AC outlet.
5
AUTO DATE AND TIME SETTING
(OPTIONAL)
If an analog channel was found during channel search, the
TV will begin Auto Date and Time setting. This feature
searches for a local PBS station that is broadcasting Date
and Time data. These data are used to automatically set
the date and time. (This may take several seconds.)
After the Date and Time are set, the lowest Digital
channel (or lowest Analog channel if no active digital
channel is stored in the Channel Scan Memory) will be
tuned.
To cancel auto Date and Time setting, press the
CHANNEL UP key. To set the Date and Time manually,
see page 24.
6
ANTENNA SELECTION (OPTIONAL)
To change the initial analog tuning system setup (from
antenna to cable or cable to antenna), use the on-screen
menu. See “Antenna Selection” on page 18.
➠
Analog
Analog
Ant
Ant
enna 34
enna 34