Filter
Top Products
11
Getting Started
Note
You cannot enjoy a picture with an S video signal if your TV does
not conform to the S video signal. When your TV does not have
an S VIDEO input, connect the component via the VIDEO INPUT
connector using the supplied audio/video connecting cord
instead of the S video cord. For details, see page 8.
Refer to the instructions supplied with your TV.
Setups for the player when using the
digital connecting cords
Connect the component via the DIGITAL OUT OPTICAL
or COAXIAL connector using an optical or coaxial digital
connecting cord (not supplied). You do not need to use
the audio connecting cord.
Some setup adjustments are necessary for the player
depending on the components to be connected.
Use the setup display to change the various settings.
For details on using the setup display, see page 63.
If your receiver (amplifier) does not have a built-
in Dolby* Digital decoder or DTS decoder
• To listen to the sound through speakers connected
to a receiver (amplifier) which has a digital
connector, or to output the sound to a digital
component such as a DAT or MD deck
Set the “AUDIO SETUP” items in the setup display
(page 73) as shown in the illustration below. These are
the default settings.
When you have made the connections using an optical or
coaxial digital connecting cord, do not set ”DOLBY
DIGITAL“ to ”DOLBY DIGITAL,“ ”DTS“ to ”DTS“ and
“48kHz/96kHz PCM” to “96kHz/24bit.” If you do, a loud
noise will suddenly come out from the speakers, affecting
your ears or causing the speakers to be damaged.
Note
You cannot make direct digital audio recordings of discs recorded
in multichannel surround format using an MD deck or DAT
deck.
If you have an audio component with a built-in
Dolby Digital decoder or DTS decoder
• When you connect an audio component with a built-
in Dolby Digital decoder A
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and
then set “DOLBY DIGITAL” to “DOLBY DIGITAL” in
the setup display (page 74).
• When you connect an audio component with a built-
in DTS decoder B
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and
then set “DTS” to “DTS” in the setup display (page 74).
• When you connect an audio component that is
compatible with 96kHz/24bit C
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and
then set “48kHz/96kHz PCM” to “96kHz/24bit” in the
setup display (page 74).
Notes
• When you do not connect an audio component with a
built-in Dolby Digital decoder, do not set “DOLBY DIGITAL”
to “DOLBY DIGITAL.”
• When you do not connect an audio component with a
built-in DTS decoder, do not set “DTS” to “DTS.”
• Do not set to “96kHz/24bit” if your receiver (amplifier) is
not compatible with 96 kHz.
• When you connect the component via the DIGITAL OUT
OPTICAL or COAXIAL connector, the Virtual 3D Surround
effect cannot be heard.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
To set, press , then .
To quit, press .
OFF
STANDARD
DOLBY SURROUND
CENTER SPEAKER EQ:
FLAT
ON
DOLBY DIGITAL
48kHz/96kHz PCM:
96kHz/24bit
DTS:
DTS
ENTER
DISPLAY
B
A
C
* Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories.
Confidential unpublished works. ©1992-1997 Dolby
Laboratories. All rights reserved.
Set the
items as
shown
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
To set, press , then .
To quit, press .
OFF
STANDARD
DOLBY SURROUND
CENTER SPEAKER EQ:
FLAT
ON
D-PCM
48kHz/96kHz PCM:
48kHz/16bit
DTS:
D-PCM
ENTER
DISPLAY