Filter
Top Products
Getting started
4
EN
Using the remote control for other
equipment
This remote control can be used to control other appliances using
the programmable buttons
VCR, DVD, SAT, AMP and AUX.
For each button you can control the following appliances:
VCR: video recorder
DVD:DVD player
SAT: satellite receiver, cable network
AMP: hi-fi system, Home Cinema amplifier
AUX: decoder for terrestrial digital TV set and any other
appliance. For instance, if you have two video recorders, you can
program the
VCR button to control one video recorder, and
program the
AUX button to control the other one.
Note:The TV button is not programmable.
Remote control TV functions
Most of your television’s functions are available via the menus that
appear on the screen.The remote control supplied with your set
can be used to navigate through the menus and to configure all the
general settings.
Standby / quit standby.
TV To access TV mode. Press this button to control the
television.
VCR To access VCR mode.
DVD To access DVD mode.
SAT To access SAT mode.
AUX To access AUX mode.
AMP To access AMP mode.
PRESETS (red button) preset settings menu.
LIST (green button) list of channels (see page 9).
INFO (yellow button) status information (see page 8).
GUIDE (blue button) programme information (see page 8).
TEXT (purple button) Teletext (see page 19).
The coloured buttons can also be used for operating Teletext.
To select menu options.
To set functions, change values, enable and disable
functions (checkbox) in menus.
To select the picture format or zoom.
OK To confirm a selection, enable and disable functions
(checkbox) in menus.
To freeze the picture (see page 9).
MENU To access the
OVERVIEW
menu.
EXIT To exit the menu structure.
+/- To control the volume.
MUTE To s witch the sound off and back on again.
RETURN To r eturn to the previous channel/AV programme.
PR+/PR- To change channels.
0-9 To select a channel by its number. In the case of channel
numbers with two digits:
- press the tens digit for a few seconds to display it on the
screen, then press the units digit or
- press
0/--
to display “
--
”, then enter the channel number.
To enter numeric values in menus.
In PC mode, the buttons
1-9
can be used to return to TV
mode and change channels.
AV To select an appliance connected to an AV socket.
DEMO (Disabled).
Playing files from memory cards
When playing mp3,WMA, JPEG, MPEG and DivX files, you can use
some of the buttons on the remote control to perform certain
functions, which vary according to the type of file.
INFO To display the Info menu.
REVERSE mp3 and WMA: to return to the previous file.
JPEG: to reduce the projection speed.
PLAY To play.
FORWARD mp3 and WMA: to go on to the next file.
JPEG: to increase the projection speed.
STOP To stop playing.
PAUSE To pause, stop at a particular picture.
MPEG and DivX: to change files.
0-9 MPEG and DivX: to select a file by its number.
Programming the remote control
Automatic code search
This method can be used to automatically find the most
appropriate code for your appliance.
1. Switch on the appliance you wish to use the remote control
with.
2. Press the relevant button for this appliance on the remote
control, and while holding this button down, press the
standby button until the appliance buttons of the remote
control come on. Release both buttons.
3. Point the remote control at the appliance and press PLAY.If
the appliance has not gone into standby mode, press the
PLAY button again to continue the search for the next set of
codes. Repeat this operation until the appliance goes into
standby mode.There are around 20 sets of codes.
4. When the appliance goes into standby mode, switch it on again
without using the remote control. Press the
REV button as
many times as is required to return the appliance to standby
mode.
5. Press the STOP button and hold it down until the appliance
buttons of the remote control go off.
Note:You can cancel the programming operation at any time by
pressing the
EXIT button.
IFC130-L_EN-2 8/12/05 15:22 Page 4