Filter
Top Products
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
17
Key Label
Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassete
(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)
TV/VCR VCR
---
TV/SAT TV/VCR --- --- --- Reverse
AM/FM --- --- --- --- Disc shift AM/FM Disc shift Deck side
DISC A/B switch
STOP VCR VCR VCR Stop Stop --- Stop Stop
REC
**
VCRVCR VCR Record** --- --- --- Record**
POP CH
yz
POP channel TV TV TV TV TV TV TV
up/down
SPLIT POP Split TV TV TV TV TV TV TV
POP DIRECT CH POP Direct ch
TV TV TV TV TV TV TV
FREEZE POP Freeze TV TV TV TV TV TV TV
SWAP POP Swap TV TV TV TV TV TV TV
CH SCAN POP
Ch scan
TV TV TV TV TV TV TV
SOURCE POP Source TV TV TV TV TV TV TV
Note:
• “---” will send nothing.
•“ TV” will jump to TV.
•“VCR ” will jump to last active VCR or DVD. Active VCR/DVD is defined as the mode that remains for a minimum of 5
seconds, or if a key is pressed in that mode.
*
The VOLUME and MUTE will jump to “TV” by default. When the volume is unlocked, all the devices will have their own volume.
The AUDIO1/2 (Receiver, CD) modes will have their own volume even if Volume Lock is on TV, CABLE/SAT, VCR, or DVD. See
“Using the Volume Lock feature” on page 18.
**
Press the REC button two times within 5 seconds to record each audio/video source.
Programming the remote control for use with
your audio/video devices
Device code setup
1. Refer to the Device code table on pages 19 – 20 to find the code
for the brand of your device.
If more than one number is listed, try each one separately until
you find the one that works.
2. Press MODE until the Mode indicator of the device (CABLE/
SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.
3. While holding down the RECALL button, press the Channel
Number buttons to enter the four-digit code of your brand of
device. If a valid code is entered, the mode indicator will blink
twice. If an invalid code is entered, the mode indicator will blink
one long blink.
4. Point the remote control at the device and press POWER to test
the code.
If the device turns on, you have entered the correct code.
If the device does not respond to the remote control, you may
have entered the wrong code. Repeat steps 3 and 4 using another
code.
Note: In addition to POWER, confirm that all necessary keys on the TV
remote control operate your device. If some keys are not operational,
repeat the device code setup using another code (if other codes are listed
for your device). If,ºafter trying all listed codes, the necessary keys do not
operate your device, use the device’s original remote control.
5. Press MODE to select the TV mode to control the TV.
123
456
789
0
TV
CABLE/SAT
VCR
DVD
AUDIO1
AUDIO2
100/
ENT
POWER
+10
ACTION
MODE
PIC SIZE
MENU
LIGHT SLEEP
ENTER
FAV
CH
VOL
EXIT
CH RTN
DVD RTN
DVD CLEAR
SLOW/DIR
SKIP/SEARCH
INPUT
RECALL
MUTE
L
I
N
K
T
H
E
A
T
E
R
F
A
V
O
R
I
T
E
I
N
F
O
G
U
I
D
E
S
E
T
U
P
T
I
T
L
E
S
U
B
T
I
T
L
E
A
U
D
I
O
FAV
POWER
Numbers
RECALL
MODE
Note:
• Every time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes.These VCRs
have a switch labeled “VCR1/VCR2.” If
your VCR has this kind of switch and does
not respond to any of the codes for your
VCR brand, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control
• Although the remote control for your new
TV includes codes for many devices, it may
not include codes for some or all of the
features on certain devices you want to
control. If you are unable to program the