Filter
Top Products
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
27
Adjusting the color convergence
This projection TV uses three separate TV tubes: red, green, and blue.
The red, green, and blue images are projected onto the screen where
they converge to form a full-color picture. You can see a clear picture
only when the three images converge correctly. Convergence may drift
over time or if you move the TV. (If the image on your screen is clear,
skip this procedure.)
To adjust the color convergence:
Note: The TV must be on for at least 30 minutes before adjusting the
color convergence.
1. Press MENU, and then press x or • until the PICTURE menu
appears.
2. Press y or z to highlight CONVERGENCE (below left).
3. Press x or • to display the center CONVERGENCE menu
(below right). If you see separate red, blue, or green crossed lines,
you should adjust the convergence.
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
P CTURE ANTENNAI
MODE SPORTS
PREFERENCE
FLESH TONE ON
OFF
COOL
NOI REDUCTIONSE
CONVERGENCE
SAVE NEW
COLOR
TEMPERATURE
234567891011 12 13 14 1516 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
3
234567891011 12 13 14 1516 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
3
EXIT TO SELECT POSI IONT:
ENTER
RED BLUE
TO SELECT COLOR:
4. Press ENTER to highlight RED or BLUE, depending on which
color needs adjusting. If both red and blue need adjusting, you
must perform steps 4 and 5 twice.
5. Press y (up), z (down), x (left), or • (right) on the remote
control to converge the red or blue line into the green line. When
correctly adjusted, you will see two single crossed white lines.
6. Press EXIT to display the circumference CONVERGENCE
menu.
7. Press the corresponding Number button (1–4 and 6–9) to select
the area you want to adjust (below left).
8. Press ENTER to highlight RED or BLUE, depending on which
color needs adjusting (below right). If both red and blue need
adjusting, you must perform steps 8 and 9 twice.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
234567891011 12 13 14 1516 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 3
3
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 3
3
PUSH 1
8
2
9
3
6
7
1
4
9–
234567891011 12 13 14 1516 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
3
234567891011 12 13 14 1516 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
3
RED BLUE
EXIT TO SELECT POSI IONT:
ENTER TO SELECT COLOR:
9. Press yzx • to converge the red or blue line into the green line,
until you see two single crossed white lines.
10. To select another area to adjust, press EXIT once, and then repeat
steps 7 through 9.
11. To close the CONVERGENCE menu, press EXIT twice.
EXIT
yzx •
Number
MENU/
ENTER