Xantech RC68+ Universal Remote User Manual


  Open as PDF
of 5
 
1
Amplifiers & Preamplifiers
RC68+
INSTALLATION INSTRUCTIONS
RC68+
PROGRAMMER / REMOTE CONTROL
The RC68+ programmer is a 55 key hand-held device that generates all the IR
codes necessary for the set up and operation of Xantech IR remote controlled
products. Such products include models ZPR68, RAT1, MIRV1, GATEKEEP-IR,
etc. The RC68+ is an upgrade of the previous 32 key RC68. While providing
additional key-code command capabilities, it retains all previous RC68 program-
ming in a similar 32 key layout section on the keypad.
GENERAL
• The RC68+ is used initially for the setup of system control parameters and IR
Code Groups for Xantech products.
• It is then used to "teach" a basic set of operational IR commands into universal
learning devices such as the Xantech URC series learning remotes, the
Xantech Smart Pads, the 590 Programmable Controller, the 710 Fone Link,
etc., for the end user.
• Included with the RC68+ is a set of keypad overlays. These overlays are marked
with command names that apply to specific Xantech models. They are provided
to make it easier for the installer when setting up the system. See Fig. 2 and
the model listings below.
• While the RC68+ will operate as a separate remote control, it is highly
recommended it not be given to the final user for the following reasons:
• Since it includes special setup codes, the user may inadvertently alter the
installer configurations.
• Also, since the user will require IR commands from other brands of equipment to control the total system,
in addition to those of the RC68+, all commands should be consolidated into one learning device, for ease
of use.
THE RC68+ OVERLAY SYSTEM
• The RC68+ base unit comes with a permanently attached keypad overlay (A) with lettering that identifies
the commands for operation of the model ZPR68 and other models with similar commands.
• Additional temporary overlays are included for use with
Xantech models that differ greatly from the ZPR68.
• The overlays are simply placed over the RC68+ keys, as
needed. Use the overlay that corresponds to the Xantech
model or models you are working with, as listed below.
Xantech Model RC68+ Overlay Id Letter
RAT1, MIRV1, ............................................ A (permanently attached
RGC11, RP41AV, to the RC68+)
RS41AV, ZPR68,
ZPR68-10
AC2, CC12, SR21 ...................................... B
RT8, RT16-10 ............................................ C
680-10, 686-10, CC62 ............................... D
Gatekeep-IR Modules ................................ E
IR-DC4 (RC68+ IR-to-RS232, Arrakis) ...... F
SmartPad
3
.................................................. I
A
60 88
A8
98
A B C ADJ-OFF
1234
5678
GLOBAL
Z-ADJ
TREBLE
VOL
MUTE
ON OFF
E-FLAT LAST MAX-V TRIM
OFF C-BAL
BASS
INPUT
80 48 10 90 01
00 C0 50 D0 41
40 A0 21
20 E0 70 F0 61
18 09
B8 29
28 E8 78 F8 69
68 C8 58 D8 49
E1 89 C9 A9 E9
71 19 59 39 79
F1 99 D9 B9 F9
08 38
30 B0
RC68+ PROGRAMMER
Permanently
attached
"A" Overlay.
A B C ADJ-OFF
1234
5678
GLOBAL
Z-ADJ
TREBLE
VOL
MUTE
ON OFF
E-FLAT LAST MAX-V TRIM
OFF C-BAL
BASS
INPUT
RC68+ PROGRAMMER
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
B
0
2
3
4
5
6
1
7
1234
5678
9101112
13 14 15 16
GP-ON GP-OFF
C
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
OFF ON TGL MMT
GP-ON
GP-OFF
D
1
3
4
5
6
2
ON OFF OPEN CLOSE
ON OFF OPEN CLOSE
ON OFF OPEN CLOSE
ON OFF OPEN CLOSE
ON OFF OPEN CLOSE
ON OFF OPEN CLOSE
ON OFF OPEN CLOSE
ON OFF OPEN CLOSE
E
1
3
4
5
6
7
8
2
1 2 3 PLAY
456STOP
7 8 9 PAUSE
CD# 0 TR# RESUME
DISC -- DISC + TR -- TR +
1 CD ALL CD SEQL RANDOM
ARTIST TITLE NUMBER ZONE
LEFT RIGHT ENTER SELECT
F
1
3
4
5
6
7
8
2
ON/TOG OFF
0
ON/TOG OFF
1
ON/TOG OFF
2
ON/TOG OFF
3
ON/TOG OFF
4
ON/TOG OFF
5
ON/TOG OFF
6
ON/TOG OFF
7
ON/TOG OFF
8
ON/TOG OFF
9
ON/TOG OFF
A
ON/TOG OFF
B
ON/TOG OFF
C
ON/TOG OFF
D
ON/TOG OFF
E
ON/TOG OFF
F
I
Overlay
Identification
Letter
A
FIG. 2 Overlays for the RC68+ Programmer
next