Emerson EWC19T1 CRT Television User Manual


 
- 31 - EN
1C29
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/DVD/VHS.
Make sure ...
TV/DVD/VHS power must be turned on.
Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
NOTES:
This function CANNOT be done from the remote
control.
Recording starts immediately when the REC/OTR
button is pressed.
When the REC/OTR button is pressed 18 times, the
TV/DVD/VHS returns to the Normal Recording
mode.
To stop the OTR operation, press the STOP button
on the TV/DVD/VHS or on the remote control.
To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up momen-
tarily then disappear.)
Recording stops when 0:00 is reached.
Please note that in the SLP mode maximum record-
ing time, assuming the tape is started at the begin-
ning, is 8 hours using T-160 (or 6 hours using T-
120).
If the tape runs out before the end time, the
TV/DVD/VHS will switch to the Stop mode imme-
diately, ejects the tape and turns itself off.
1 Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL K or L button.
Remember: If the TV/DVD/VHS is connected to a
cable box or satellite box, the TV/DVD/VHS must be
on CH3 or CH4, then the channel to be recorded is
selected on the cable box or satellite box.
2 Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3 Begin OTR
Press the REC/OTR button on the
TV/DVD/VHS as many times as
needed. The recording length will
be determined by the number of
times you press the REC/OTR button. Each addition-
al push will increase the recording time by 30 min-
utes. It is set up to 8 hours.
OTR (One Touch Recording)
Push(es) Display Recording length
1 push (normal recording)
2 pushes 0:30 30 minutes
3 pushes 1:00 60 minutes
17 pushes 8:00 480 minutes
You can make copies of video tapes made by friends
or relatives for your enjoyment.
Connect your TV/DVD/VHS and a Source (Playing)
VCR using the following diagram.
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to
record over, into the TV/DVD/VHS’s cassette com-
partment.
3)Press the SPEED button on remote control for the
TV/DVD/VHS to select the desired recording
speed (SP/SLP).
4)Press the CHANNEL
K or L button on the
TV/DVD/VHS until “AUX” appears on the screen.
5)Press the RECORD button on the TV/DVD/VHS.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/DVD/VHS’s front panel controls whenever pos-
sible. The remote control might affect the source
(Playing) VCR’s playback operation.
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
L-AUDIO-RVIDEO
HEADPHONE
VIDEO
IN
OUT
AUDIO
IN
OUT
L
R
[Fig.8]
[Ex: Source (playing)
VCR or camcorder]
Audio/Video
adapter cable
(not supplied)
[The TV/DVD/VHS]
OTR(2 : 30)
SP
TD351_01-35 02.2.18 1:41 PM Page 31