Filter
Top Products
6. PROGRAM
7.CD PLAY/PAUSE
8.LCD DISPLAY
9.CFD
10. V OLUME CONTROL
11.CD STOP SWITCH
12.CD SKIP-
13. TUNING
14. CD SKIP+
15. B AND SWITCH
16 SPEAKER
17. CASSETTE RECORD SWITCH
18. CASSETTE PLA Y SWITCH
19. CASSETTE REW SWITCH
20. CASSETTE FWD SWITCH
21 CASSETTE STOP/EJECT SWITCH
22. CASSETTE PAUSE SWITCH
23. CASSETTE HOLDER
24 .A NTENNA
25. B ACK COVER
26. S PEAKER OUTPUT
TERMINAL(RIGHT).
27 SPEAKER OUTPUT
TERMINAL(LEFT)
28. A C SOC KET
29. A UDIO OUT
30. V IDEO OUT
31. JOYSTICK T ERMINAL
specifications
Frequency Range FM:88-108MHz,AM:530-1700KHz
Power Requirements 120V,60Hz
Specifications are subject to change for performance improvem ent without notice.
POWER SUPPLY
AC OPERATION
- THE AC POWER COR D IS LOCATED
- PLUG THE AC LINE CORD INTO ANY NORMAL HOUSEHOLD AC MAINS
OUTLET IN CORRECT VOLT AGE AND THE MAINS SOCKET.
STANDBY INDICATOR
When the power is connected to AC outlet, the STAND BY LED indicator will light up. You
have to press the POWER button on the unit or POWER button on the remote to turn on
the unit.
RADIO OPERATION
1. Connect the unit to the power source.
2. Slide the FUNCT ION SWITCH to "RADIO" position.
3. Se lect desired wav e band with the BAND S WITCH.
4. Tune to desi red station by rotating the TUNING KNOB.
5. Gently rotate this control back & forth unti l you get the strongest, clearest sound.
6. The built-in MW(AM) or LW antenna and the SW antenna rod are directional. When
receiving SW broadcast, extend the SW ELESCOPIC ANTENNA in full length.
The stronges t re ception can be ach ieved by rotating the set for MW(AM) or LW or
Telescopic Antenna for FM or SW.
7. Ad just the VOLU ME KNOB to your listening preference.
8. To turn off the radio, slide the FUNCTION SWITCH to "TAPE" position.
CASSETTE OPERATION
PLAYBACK OF CASSETTE
Be sure to tighten any slack tape in th e cassette before use, using either a pencil or a
ball-point pen, simply in sert the pen or pencil into the centre of spool and ro tate to remove
slackess.
Depress the S TOP/EJECT button to open the cassette door.
Insert the cassette into the compartment with the open end facing upward and the full reel
on the left hand side, push the cassette well down and clos e the door, be sure not to touch
the tape surface. Set the Function switch to "TAPE " position and press the cassette play
button. To stop playback, press the STOP/EJECT b utton again.
AUTO STOP
When the tape reaches the end during play back or recording, the built-in auto stop system
will release the depress ed play, record keys. The auto stop system operates while
recording from the built-in radio or CD player, only the cas sette function is brought
automatically to stop mode and the radio or CD Player will continue to play.
TAPE RECORDING
A. Install a cassette tape.
B. Set FUNCT ION SWITCH to "RADIO" position. After selecting the desired band and
tune the T UNING KNOB to desired broadcast s tation. Then push down RECORD
BUTTON and PLAY BUTTON simultaneou sly.
C. After recording the desired broadc ast, depress the STO P/EJECT BUTTON lightly, and
then set FUNCTION SWITCH to "TAPE" position in order to listen to the recorded
broadcast.
D. If you desire to play reco rded broadcast, please follow the instructions explained in
playback sec tion.
Note: Tape recording is also available for VCD/CD/MP3 playback (set FUNCTION
SWITCH to "VCD/CD/MP3" position). Similar as radio recording.
External MIC recording: S et FUNCTION SWITCH to "TAPE" position, pre ss the RECORD
BUTTON and PLAY BUTTON simultaneou sly and speak through external MIC.
TYPES OF CASSETTE
Use only good quality cassettes (IEC TYPE 1) for making recordings. Ma y be used to
replay other ty pes of cassette but is unable to make proper recordings on these more
specialized tapes.
The us e of C120 cassettes is NOT recommended in this ma chine.
PROTECTING RECO RDING
24
27
26
25 28
29
30
31
8
10
3
11
5
6
13
12
4
97
2
14
17
18
19
20
21
22 23
15
16 16
8
10
3
11
5
6
13
12
4
97
2
14
17
18
19
20
21
22 23
15
16 16
24
27
26
25 28
29
30
31
6.PROGRAMA
7.REPRODUCCIÓN/PAUSA DEL CD
8.PANTALLA LCD
9.CFD
10.CONTROL DE VOLUMEN
11.BOTÓN DETENER DEL CD
12.SALTO DEL CD -
13.SINTONIZADOR
14.SALTO DEL CD +
15.BOTÓN DE BANDAS
16.ALTAVOZ
17.BOTÓN DE GRABACIÓN DEL CASETE
18.BOTÓN REPRODUCIR DEL CASETE
19.BOTÓN RETROCEDER DEL CASETE
20.BOTÓN ADELANTAR DEL CASETE
21.BOTÓN DETENER/EYECTAR DEL CASETE
22.BOTÓN PAUSA DEL CASETE
23.SOSTÉN DEL CASETE
24.ANTENA
25.TAPA TRASERA
26.SALIDA DEL ALTAVOZ (DERECHA)
27.SALIDA DEL ALTAVOZ (IZQUIERDA)
28.ENTRADA AC
29.SALIDA DE AUDIO
30.SALIDA DE VÍDEO
31.SALIDA DE LOS MANDOS
ESPECIFICACIONES
Rango de frecuencia: FM: 88-108MHz, AM: 530-1700KHz
Requisitos de energía: 120V, 60Hz
Las especicaciones estar sujetas a cambio con el n de hacer mejoras sin previo aviso.
FUENTES DE ENERGÍA
Con energía AC
-Conecte el cordón AC
-Enchufe el cordón AC a un tomacorriente doméstico que cuente con el voltaje correcto.
INDICADOR STANDBY
Cuando el aparato se encuentre conectado a la electricidad, la luz indicadora STANDBY se
iluminará. Debe presentarse el botón POWER en el aparato o en el control remoto para encender
el equipo.
FUNCIONAMIENTO DE LA RADIO
1.Conecte el equipo al tomacorriente.
2.Coloque el selector de FUNCIONES en la posición RADIO.
3.Seleccione la banda deseada con el selector de BANDAS.
4.Sintonice la estación deseada girando el control de sintonización.