Filter
Top Products
23
Model D2424LV Quick Operation Guide
Changing the program FS
In the following, we will change a program’s sampling frequency in the current drive.
IN general, tha sampling frequency of the program made in the current drive will be the value set during
the most recent formatting of the current drive. But even after a program has been made, the sampling
frequency can be changed. However, the changes will be limited as follows depending on the quantizing
figure when formatting.
<Note>
• Do not change the sampling ferquency of a completed program.
• Changing of the sampling frequency will be limited by the quantizing figure (16bit or 24bit) set at
formatting of the current drive.
Current drive formatting by 24bit:
A program in 44.1kHz, 48kHz, 88.2kHz or 96kHz can be made.
Current drive formatting by 16bit:
A program in 44.1kHz or 48kHz can be made.
• Please remember the following points should there be programs with a different FS in the current
drive.
* Do not copy or paste between programs with different FS. Fostex cannot take responsibility in
compensation of data which had been “copied” or “pasted” between programs with different FS.
* In the section “Digital recording” explained above, be sure to set the external digital equipment
sampling frequency the same as that of the program.
1. First, start the program in which the FS is to be
changed by using the “program change” menu
explained above.
2. Press the [SETUP] key to enter the SETUP mode.
The display will change to SETUP mode.
3. Rotate the Jog dial to display the “Sample Rate?”
menu and then press the [EXECUTE/YES] key.
When the [EXECUTE/YES] key is pressed, the FS figure of
the current activated program will flash and the recorder
will enter the editing mode.
4. Display the desired FS by rotating the Jog dial, an
then press the [EXECUTE/YES] key.
Either “44.1” or “48” can be selected in the 16bit current
drive, “44.1,” “48,” “88.2,” or “96” can be selected in the
24 bit current drive. After selection, the recorder will be
set to the chosen FS when the [EXECUTE/YES] key is pressed.
5.Exit from the SETUP mode by pressing the [EXIT/
NO] key or [STOP] button.
<Note>
If you change the FS (44.1 or 48kHz) of a program
in the 24-track mode to 88.2 or 96kHz, the
program automatically changes to the 8-track
mode and track numbers 1 through 8 on the
display are lit.
The following shows display examples when
changing the FS of a 48kHz/24bit program to
96kHz.
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
2322
21
20
19
18
17
1615141312
11
10
98765
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
2322
21
20
19
18
17
1615141312
11
10
98765
4
3
2
1
CLOCK
INT
FSM
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
ABS
2322
21
20
19
18
17
1615141312
11
10
98765
4
3
2
1
CLOCK
INT
FSM
∞
42
OL
0
30
24
18
12
9
6
3
kHz
FS
BIT
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
ABS
8765
4
3
2
1
CLOCK
INT
Track numbers 1 through 8 are lit.
Flashing
Flashing