Filter
Top Products
13
Blu-Ray Disc Player
www.insigniaproducts.com
4 Press or to select On or Off. Off selects a 60
frames/second output format.
5 Press to go to the previous menu.
Selecting the PCM downsampling rate
To select the PCM downsampling rate:
1 Press ENTER. The Settings menu opens.
2 Press , press or to select Audio. The Audio
menu opens.
3 Press to select PCM Downsampling, then
press ENTER.
4 Press one or more times to select the PCM
downsampling rate you want. You can select
48KHz, 96KHz, or Off.
• If you have a surround sound amplifier
connected to your player through the SPDIF
jack, select the highest sampling rate the
receiver supports. See the documentation that
came with the receiver.
• If you do not have a surround sound amplifier
connected to your player, select 48KHz.
• If you have a surround sound amplifier
connected to your player through the analog
audio L and R jacks, select 48KHz.
• If you have a surround sound amplifier
connected to your player through the HDMI
output, select 48KHz.
5 Press to go to the previous menu.
Selecting the digital audio output mode
To select the digital audio output mode:
1 Press ENTER. The Settings menu opens.
2 Press or to select Audio. The Audio menu
opens.
3 Press , press or to select Digital Output,
then press ENTER.
4 Press or to select the digital output mode
you want, then press ENTER. You can select:
• PCM—Sends mixed digital audio over the
HDMI connection in 7.1CH PCM (if supported
by HDMI device) and the SPDIF connection in
two-channel PCM format.
• Bitstream HD—Sends the original bitstream
from the disc over the HDMI and SPDIF
connections using highest quality possible.
HDMI has the higher quality capabilities with
advanced audio codecs like TrueHD and
DTS-HD. Blu-ray audio is limited to the
soundtrack for the main movie (no PIP audio
and no effects audio).
• Bitstream Legacy—Sends the original
bitstream from the disc over the HDMI and
SPDIF connections using legacy audio
formats. Blu-ray audio is limited to the
soundtrack for the main movie (no PIP audio
and no effects audio).
• Bitstream mixed—Sends mixed and encoded
Blu-ray audio streams in a single bitstream.
This mode is primarily intended for use with
SPDIF 5.1CH receivers to produce mixed
Blu-ray audio in surround sound.
5 Press to go to the previous menu.
Turning dynamic range control on or off
Dynamic range control is only active when a Dolby
Digital signal is detected.
When Dynamic Range Control is set to Off, movie
soundtracks are played with the standard dynamic
range.
When movie soundtracks are played at low volume
or from smaller speakers, you can set Dynamic
Range Control to On. Your player applies
appropriate compression to make low-level content
more intelligible and prevent dramatic passages
from getting too loud.
To turn dynamic range control on or off:
1 Press ENTER. The Settings menu opens.
2 Press or to select Audio. The Audio menu
opens.
3 Press , press or to select Dynamic Range
Control, then press ENTER.
4 Press or to select On or Off.
5 Press to go to the previous menu.
Note
Incorrectly setting the digital audio output’s PCM
sampling rate may result in unpredictable audio
playback.
Settings
Audio
PCM Downsamp ling
Digital Output
Dynamic Range Control
48 K hz
PCM
O
Language
Audio
Network
System
Display
Parental
Settings
Audio
PCM Downsamp ling
Digital Output
Dynamic Range Control
48 K hz
PCM
O
Language
Audio
Network
System
Display
Parental
Settings
Audio
PCM Downsamp ling
Digital Output
Dynamic Range Control
48 K hz
PCM
O
Language
Audio
Network
System
Display
Parental