Filter
Top Products
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Left+
64 EN
EDITING
Page 64 Thursday, 3 June 2004 10:46
NOTES:
● If you have a satellite receiver or a decoder connected to the L-2 IN/
DECODER connector, be sure to set “L-2 SELECT” back to
appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the L-2
IN/DECODER connector, leave “L-2 SELECT” set to “VIDEO”.
● When “L-2 SELECT” is set to “SAT VIDEO” and “SAT S-VIDEO”,
“SAT” appears on the TV screen or front display panel instead of
“L-2”.
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set
“L-2 SELECT” to “DECODER” or “SAT VIDEO”.
● If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2
SELECT” to “DECODER” or “SAT S-VIDEO”.
● If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT
VIDEO”, “SAT S-VIDEO” or “DECODER”, be sure to connect the L-1
IN/OUT connector with a TV.
F-1 Input Setting
Set “F-1 INPUT” to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting”
(੬ pg. 63).
2 Press rt to select “F-1 INPUT”, then press ENTER.
3 Press rt to select the
appropriate setting, then press
ENTER.
4 Press SET UP to complete the
setting.
*The boldface settings below
indicate the settings at your
purchase.
8 F-1 INPUT — VIDEO / S-VIDEO
VIDEO: When connecting an appliance to the VIDEO input
connector, set to “VIDEO”.
S-VIDEO: When connecting an appliance to the S-VIDEO input
connector, set to “S-VIDEO”.
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
Example: Dubbing to an MD
1 Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
2 Place a disc on the unit and load an MD on the connected digital
audio device.
3 Select the audio to be dubbed.
4 Start playback slightly before the actual point from where you
wish to start dubbing.
5 Press 9 to pause playback.
6 Select the input mode on the connected digital audio device.
7 Press 4 to start playback on the unit.
8 Start recording on the digital audio device.
9 Stop recording on the digital audio device. Then press 8 to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where you
intend editing to start, and where it actually starts.
VIDEO IN/OUT
L-2 SELECT
MONITOR TYPE
VIDEO
4 : 3LB
L-1 INPUT VIDEO
FUNCTION SET UP
PRESS [SET UP] TO EXIT
ENTER
SELECT
EXIT
SET UP
SELECT WITH [ ] THEN PRESS [ENTER]
DISPLAY SETREC/PLAY SET UP
DVD VIDEO SET UP INITIAL SET UPHDD/DVD SET UP
CONECT
L-1 OUTPUT
SCART VIDEO
F-1 INPUT
VIDEO
VIDEO
S-VIDEO
Digital Audio Dubbing
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
Rear of unit
Note for connection:
Remove the protection cap from the cable.
Digital audio device
(MD deck, etc.)
Coaxial cable
(not provided)
DIGITAL OUT
(COAXIAL)
Player
Recorder
Optical cable
(not provided)
DIGITAL OUT
(OPTICAL)
DR-MH30EU_00.book Page 64 Thursday, June 3, 2004 11:00 AM