Filter
Top Products
Masterpage:Right+
EN 93
Filename [MV5SEK_13Subsidiary.fm]
TROUBLESHOOTING
Page 93Wednesday, 31 August 2005 19:58
● The satellite receiver is not connected properly to this unit.
] Connect the satellite receiver to the [L-2 IN/DECODER]
connector properly. (੬ pg. 76)
● Power failure occurred.
] Set date and time correctly. (੬ pg. 88)
● 8 programmes have already been timer programmed.
] Clear unnecessary programmes on the unit, then try timer
programming again. (੬ pg. 34)
● The PC’s data recorded on a DVD-RAM drive cannot be cleared
on this unit.
] Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (੬ pg. 9, 89)
Timer Recording (VHS Deck)
● No tape is loaded.
] Press TIMER # so that the VHS timer indicator lights off. Load a
cassette with the record safety tab intact, then press TIMER #
again.
● Date and time is not correct.
] Set date and time correctly. (੬ pg. 88)
● The timer is not engaged.
] Press TIMER # and confirm that the VHS timer indicator lights
up on the front panel display.
● Timer recording is in progress.
] Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
● Date and time is not correct.
] Set date and time correctly. (੬ pg. 88)
● The timer is not engaged.
● Press TIMER # and confirm that the VHS timer indicator lights
up on the front panel display.
● The timer is engaged but there’s no cassette loaded.
] Load a cassette with the record safety tab intact.
● The loaded cassette has had its record safety tab removed.
] Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
● The end of the tape was reached during timer recording.
] The programme may not have been recorded in its
entirety. Next time make sure you have enough time on
the tape to record the entire programme.
● The end of the tape was reached during Instant Timer
Recording.
] The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
● Date and time set on the unit is not correct.
] Set date and time correctly. (੬ pg. 88)
● The channel position does not correspond to that in the
receiving area.
] Set the correct channel position for the receiving broadcast.
(੬ pg. 85)
● The unit’s channel positions have been set incorrectly.
] Refer to “VIDEO Plus+ System Setup” (੬ pg. 83) and
reperform the procedure.
Other Problems
For composite connection
] Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights off on the front display panel.
For component video connection
] Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights up on the front display panel.
● Those channels have been designated to be skipped.
] If you need the skipped channels, restore them. (੬ pg. 85)
● Recording is in progress.
] Press 9 to pause the recording, change channels, then press 4
to resume recording.
● After the manual settings were made, Auto Channel Set was
performed.
] Perform “Manual Channel Set” (੬ pg. 85).
] Reset the unit by disconnecting the AC power plug from the AC
outlet and connect again.
Automatic Satellite Programme Recording does not start.
On the front display panel, “– –:– –” appears.
“PROGRAMME FULL” appears on the TV screen during timer
programming.
The disc space does not increase when recorded titles are
cleared.
“NO TAPE” appears on the front display panel.
Timer programming cannot be made.
Timer programming recording does not start.
The VHS timer indicator on the front display panel won’t stop
blinking.
The tape is automatically stopped and “[’’ and the VHS timer
indicator on the front display panel won’t stop blinking.
VIDEO Plus+ Timer Programming cannot be made.
The VIDEO Plus+ system does not timer-record properly.
The image of the TV broadcast appears distorted on the TV
screen.
When scanning channels, some of them are skipped over.
The channel cannot be changed.
Channel settings that were made manually seem to have
changed or disappeared.
Malfunction occurs and the unit cannot be power off.
MV5SEK_00.book Page 93 Wednesday, August 31, 2005 7:58 PM