Filter
Top Products
June 30, 2003 6:18 pm Page 14
— 14 —
Master Page: Right
NOTES:
● Auto Satellite Prog recording is only possible with the rear
AUDIO/VIDEO IN connectors.
● When the Auto Satellite Prog Rec mode is engaged or the
recorder's power is turned off after Auto Satellite Prog recording
is finished, the recorder will not enter the Timer mode even
though “AUTO TIMER” is set to “ON”.
● For timer programming of the satellite receiver, refer to the
instruction manual of the satellite receiver.
● Auto Satellite Prog recording is not possible if your satellite
receiver does not have a timer.
● The REC LINK indicator blinks while Auto Satellite Prog
recording is in progress.
● Pressing the recorder's 1 button while Auto Satellite Prog
recording is in progress turns off and recorder's power and
disengages the Auto Satellite Prog Rec mode.
● If there is more than one satellite program you wish to record
with Auto Satellite Prog Recording, it is not possible to set a
different tape speed for each; the tape speed selected in step 1
will apply to all the programs for Auto Satellite Prog recording.
● The B.E.S.T. (
੬
15) does not work while Auto Satellite Prog
recording is in progress.
● Depending on the type of satellite receiver, the recorder may not
record a short portion at the beginning of the program or may
record slightly longer than the actual length of the program.
● If you engage the Auto Satellite Prog Rec mode when the
satellite receiver's power is on, the recorder will not start Auto
Satellite Prog recording even though the button's light blinks.
When the satellite receiver shuts off once and is turned back on
again, the recorder starts recording.
● You can also record a program from your cable system in the
same way if the system has a timer and is connected to the
recorder's rear AUDIO/VIDEO IN connectors.
● When you press the recorder's REC LINK button to engage the
Auto Satellite Prog Rec mode, if the REC LINK indicator does
not light but instead blinks quickly even though your satellite
receiver's power is off, Auto Satellite Prog Recording will not
work properly with that satellite receiver*.
If this is the case, perform “Express Timer Programming”
(
੬
pg. 11) to timer-record a satellite program.
* Some satellite receivers output signals even if the power is off. Auto
Satellite Prog Recording is not possible with those satellite receivers.
● After Automatic Satellite Program Recording, the number of
recorded programs will not be displayed on the front display
panel for the instant Review function (
੬
8).
Navigation
Navigation Playback
This function is useful when you wish to quickly find out what
programmes you have recorded on a tape with this recorder. This
function allows you to select a programme to watch, and then
automatically searches for the start of the programme. (
੬
8)
A
Load a recorded cassette
Insert a cassette recorded on this recorder.
B
Access Main Menu screen
Press MENU.
C
Access Programme Navigation screen
Press PUSH JOG rt to place the pointer
next to “PROGRAMME NAVIGATION”,
then press OK or PUSH JOG e.
D
Select a programme
Press PUSH JOG rt to place the pointer
next to the programme you want to watch.
E
Start playback
Press OK. “SEARCHING” appears on the
TV screen. Playback begins automatically
after the selected programme is located.
NOTES:
● You cannot edit programme title or delete tape data for the
cassette with the record safety tab removed.
● Programme Navigation is possible with the cassettes recorded
with this recorder only.
● Before recording, make sure the recorder’s clock is set correctly.
● Program Navigation may not work properly depending on the
tape being used.
● To record the programme information in this recorder’s memory,
you must continue to record each programme for over the
minimum recording time;
PAL
8 minutes for the SP mode
15 minutes for the LP mode
23 minutes for the EP mode
NTSC
5 minutes for the SP mode
15 minutes for the EP mode
● You can store programme information for up to 8 programmes
on one cassette. At maximum informations for 10 tapes can be
restored.
● The programme information is stored in this recorder’s memory.
If the memory in this recorder should ever be damaged and the
programme information lost, it is impossible to restore that
information.
A
TTENTION
● Be sure not to turn on the satellite receiver before the program
is executed; otherwise, the recorder will start recording when
the satellite receiver's power is turned on.
● If you have connected another appliance other than a satellite
receiver to the rear AUDIO/VIDEO IN connectors, be sure
not to engage the Auto Satellite Prog Rec mode; otherwise,
the recorder will start recording when the connected
appliance's power is turned on.
● Auto Satellite Prog recording and timer-recording cannot be
done at the same time.
Program Navigation
Turn on the TV and select the VIDEO channel (or AV mode).
Programme Navigation Screen
A Recording date
B Recording start time*
C Station name*
* After entering the programme title (
੬
15), programme title
appears instead of the recording start time and station name.
D Currently selected programme
E Programme title*
* Before entering the programme title (
੬
15), recording start time
and station name appear instead of the programme title.
PROGRAMME NAVIGATION
FUNCTION SET
TUNER SET
INITIAL SET
MAIN MENU
[MENU] : EXIT
[R/T]
[MENU] : EXIT
[R/T]
[&] : DELETE
[1] : TITLE
[MENU] : EXIT
[R/T]
[&] : DELETE
[1] : TITLE
HR-S6960AA_EN.fm Page 14 Monday, June 30, 2003 6:18 PM