Filter
Top Products
June 30, 2003 6:18 pm Page 17
— 17 —
Master Page: Right
Remote Control Functions
Remote A/B Code Switching
The remote control is capable of controlling two JVC video
recorders independently; one set to respond to the remote
control's A code control signals and another set to respond to B
code control signals. The remote control is preset to send A code
signals because your video recorder is initially set to respond to A
code signals. You can easily modify your video recorder to
respond to B code signals.
A
Set remote control code for remote control
A Press and hold VCR.
B Press the number key “2”.
C Press OK, and release VCR.
● The remote control now can transmit B code control signals.
B
Check remote control code for decorder
Press and hold 4 on the recorder for more than 5 seconds while
the recorder is turned off. The code currently set appears on the
display panel.
C
Change code for recorder
Press any key on the remote control. The recorder now responds
to B code control signals.
To control two recorders with the same remote control
You can control two JVC recorders by switching the remote
control code for the remote control between A and B (
੬
step 1),
keeping two recorders to different control codes.
● To change only the remote control code for the remote control,
DO NOT perform steps 2 and 3.
NOTE:
To set the recorder back to respond to A code signals, repeat the
same procedure as shown above except pressing number key "1"
instead of "2" in step 2 of 1.
TV Multi-brand Remote Control
Your remote control can operate the basic functions of your TV
set. In addition to JVC TVs, other manufacturer's TVs can also be
controlled.
A
Turn on TV
Turn on the TV using the Power button on the TV or its remote
control.
B
Set TV brand code
A Press and hold TV.
B Press the number keys to enter your unit’s brand code.
C Press OK, and release TV. Check if the TV's power goes off as it
should. If it does, try other operations (
੬
step 2).
● Once you have set the remote control to operate the TV, you
don't have to repeat this step until you replace your remote
control's batteries.
● Some TV brands have more than one code. If the TV does not
function with one code, try entering another.
C
Operate TV
First, press TV to set the remote control to TV mode, then press
one of the following buttons: 1, TV/VCR, TV PR +/–, ^
(TV Muting), TV %+/– (TV volume), and the number keys.
● For some brands, you must press OK after having pressed the
number keys to enter a channel number.
IMPORTANT
Although the provided remote control unit is compatible with JVC
televisions, as well as many other models, it may not work with
your TV, or in some instances, may have limited function
capability.
Special Features
Control Your TV Using Additional Buttons
Use the number keys, and the p button, & button or #
button to select the TV's channel.
● With televisions under Code 01, 02, 07, 08, 10, 11, 14, 20,
22, 23, 24, 25, 27, 33, 35, 38, 40 or 42, the p button
corresponds to the 1-digit/2-digit entry switching button
(often labelled – /– –) of your TV's remote control.
● With televisions under Code 01, 16, 28, 29, 34 or 39, the &
button corresponds to the 10 + button, and the # button
corresponds to the 20 + button of your TV's remote control.
NOTE:
The way these buttons are used is determined by your TV. Use
these buttons as instructed for your TV's remote control.
TV BRAND
NAME
CODE TV BRAND
NAME
CODE
JVC
AIWA
BEIJING
CCE
CHANGHONG
DAEWOO
FERGUSON
FINLUX
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JINXING
KONKA
LG/GOLDSTAR
01, 23, 24, 25
36
22
02
34
17, 37
27
30
32
15
19
10
28
38
40
18
MITSUBISHI
MIVER
NEC
NOBLEX
NOKIA
PANASONIC
PEONY
PHILICO
PHILIPS
SAMSUNG
SANYO
SHARP
SONY
TCL
THOMSON
TOSHIBA
03
29
20
22
31
04, 11
34, 38, 39
10, 17, 21
02, 42
12, 33, 34, 35
13, 16
06
07
41
26
08, 14
A
TTENTION
The remote control can operate not only the video recorder but
also some of your TV, cable box, satellite receiver and DVD.
● To operate your video recorder, first press the VCR button to
set the remote control to the Video mode.
● To operate your TV, first press the TV button to set the remote
control to the TV mode.
● To operate your satellite receiver, cable box or DVD, first
press the CABLE/SAT/DVD to set the remote control to the
satellite receiver, cable box or DVD mode.
HR-S6960AA_EN.fm Page 17 Monday, June 30, 2003 6:18 PM