JVC SR-L910EK VCR User Manual


 
24
1 7 : 3 0 : 0 1 3 H
30 6 98
MAIN MENU
PROGRAM TIMER
FUNCTION
ALARM IN
POWER LOSS
HOUR METER
CLOCK ADJUST
PRESS (SHIFT, SET)
PRESS (MENU) TO END
CLOCK ADJUST
YEAR 2000
MONTH 1
DAY 1
HOUR 0
MINUTE 0
PRESS (SHIFT, SET)
PRESS (MENU) TO END
CLOCK ADJUST
YEAR 1998
MONTH 6
DAY 30
HOUR 17
MINUTE 30
PRESS (SHIFT, SET)
PRESS (MENU) TO END
6 PREPARATION
[SHIFT +/-] button and
[SET +/-] button
[MENU] button
(Date/time setting screen)
[SET +/-] button
(Main menu)
(Normal screen)
Set the date and time using the CLOCK ADJUST menu
screen.
Turn on this unit and the monitor and engage the Stop mode.
Press the [MENU] button to display the main menu screen.
Press the [SHIFT +] or [SHIFT -]button to select <CLOCK ADJUST>.
(Set the cursor arrow to <CLOCK ADJUST>.)
Press the [SET +] or [SET -] button to display the CLOCK ADJUST
screen on the monitor.
Select the item to be set.
Press the [SHIFT +] or [SHIFT -] button to select the item.
[
The selected item will blink.
Enter the value for the selected item with the [SET +/-] button.
Press the [SET +] button to increase the number.
Press the [SET -] button to decrease the number.
The setting range for the year is from 1997 to 2096.
This VCR uses the 24-hour clock.
If an invalid date is set, it is automatically corrected.
(e.g.) 1999-2-29 [ 1999-2-28
Repeat steps 5 and 6 until the year, month, date, hour, and minutes
have all been set.
End date and time setting.
Press the [MENU] button twice.
[
The normal display is restored and the set date and time are shown
on screen. The time count starts from 00 seconds.
Note:
If you press the [OPERATE] button after setting the date and time
without first pressing the [MENU] button, the set date and time are
canceled.
(Menu switch <POSITION> set to L-UP)
Turn the power on.
Press the [COUNT/CLOCK] button for at least 2 seconds.
The year indication blinks in the display.
Enter the value for the year with the [SET+] or [SET-] button.
Press the [SHIFT+] button: the
month indication blinks.
Press the [SHIFT+] or [SHIFT-] button to move the blinking section.
Enter the value for the blinking section with the [SET+] or [SET-]
button.
Set the month, day, hour and minute with the [SHIFT+/-] and
[SET+/-] buttons.
When you have finished setting, press the [COUNT/CLOCK] button.
The display returns to the clock display mode and the time count
starts from 00 seconds.
Time indication on the VCR's display
When the power is turned off, the time is displayed. When the power is turned on, set the time display mode with the
[COUNT/CLOCK] button to display the current time.
The first time you turn on the power, the time display shows a blinking "0:00:00".
When the built-in backup battery capacity is low, the error indication E-10 appears on the display. Contact your local JVC
dealer to replace the built-in battery.
Set the date and time on the front panel display
MONTH
DAY
HOUR
MINUTE
YEAR
25
PAL
During daylight savings time
Set the time with one-hour delay.
After setting the time, set the <SUMMER TIME> switch to
"ON".
The set time advances one hour.
At the end of the daylight savings time season, set the
<SUMMER TIME> switch to OFF.
The standard time instead of "Summer Time" is displayed.
Set whether or not the Summer Time mode is engaged with
the <SUMMER TIME> function menu switch on the VTR mode
2 setting screen.
When the <SUMMER TIME> switch is set to "ON", the
currently set time is advanced one hour.
6 PREPARATION
6-4 Selection of Record/Play Mode
6-3 Summer Time Compensation
When setting the time, make sure the <SUMMER TIME>
switch is set to "OFF".
When the unit is shipped, this switch is set to "OFF".
Clock setting is not possible during timer recording.
Standard time
Set the clock to the actual time.
When daylight savings starts, set the <SUMMER TIME>
menu switch to "ON".
The time advances one hour on the display
Press the [OPERATE] button to turn the operating mode on.
The [OPERATE] indicator lights.
Select the recording/playback time mode with the [TIME MODE] button. Refer to the table below for more information on each
mode.
Each time the [TIME MODE] button is pressed, the recording mode changes in the following order:
3H (VHS SP mode) [ L12H (12-hour Timelapse mode) [ L24H (24-hour Timelapse mode) [ 3H (VHS SP mode) ...
Playback Time Mode will differ depending on how the function menu switch <NOISELESS PLAY> is set.
When NOISELESS PLAY is set to OFF: 3H (VHS SP mode) [ L12 (12-hour Timelapse mode) [ L24
(24-hour Timelapse mode) [ 3H (VHS SP mode) ....
When NOISELESS PLAY is set to ON: 3H (VHS SP mode) [ 12 (12-hour Noiseless playback mode) [ 24 (24-hour Noiseless
playback mode) [ 3H (VHS SP mode) ....
The selected recording or playback time mode is shown on the display.
The SP indicator lights.
Note:
When a tape recorded in the VHS Long Play (LP) mode is played back, the LP indicator lights. Recording in the LP mode is
not possible with this unit.
SP indication
[TIME MODE] button
Display section
Recording/
playback time
mode indication
LP indication
* Recording time varies depending on the type of cassette used.
* For optimum performance and reliability, use a tape with a standard recording time of 180 minutes (E-180) or less.
* You can set 12H and 24H only during Playback Mode.
Available recording time (hour)
E-30 E-60 E-90 E-120 E-180
3H VHS Standard (SP) 0.5 1 1.5 2 3 Possible (Continuous) 23.39 mm/sec.
L12H 12-hour Timelapse 2 4 6 8 12 0.1 Possible (Continuous) 4.68 mm/sec.
L24H 24-hour Timelapse 4 8 12 16 24 0.18 Possible (Continuous) 2.60 mm/sec.
12H 12-hour Noiseless 2 4 6 8 12 0.1 Impossible Continuous field advance
24H 24-hour Noiseless 4 8 12 16 24 0.18 Impossible Continuous field advance
Modes
Recording/
playback
interval (sec.)
Audio
recording
Display
indi-
cations
Tape
running