Filter
Top Products
10
2 CONTROLS AND CONNECTORS
2-2 Display
2
3
4
5
1
6
8
9
11 12
13
7
10
14
TIMER indication
Lights during timer recording programming/operation.
REPEAT indication
Lights when the VCR is in the Repeat Record mode.
OVERLAP indication
Blinks when programs scheduled for timer recording
overlap.
Timer program number
During timer recording, the number of program being
recorded blinks.
When the timer recording ends, this number goes out.
AL (alarm) indication
Shown during alarm recording. Blinks when alarm
recording ends.
VISS indication
Shown when the alarm recording start point is index-
searched. For details, refer to
“Index Search” on page
42.
LOCK indication
Lights when the operation lock function is activated.
AL REC (alarm recording) indication
Lights when the function menu switch <ALARM REC> is
set to “ON”.
SENSOR REC (sensor recording) indication
Lights when the function menu switch <SENSOR REC>
is set to “ON”.
Operation mode display
Shows the operation modes.
Playback Recording
Rewind
Fast-
forward
Continuous field
advance playback
Still
Record-
pause
Rewind
search
Fast-forward
search
Reverse
playback
* (
) mark in the Rec/Pause mode is shown in red.
Cassette indication
Lights when a cassette is loaded. Blinks when a
cassette is being ejected.
SP/LP indication
Shows the VHS standard (SP) mode during recording/
playback.
During Timelapse Recording/Playback mode, the SP
indicator is shown.
Tape counter/time indication
• When the power is turned on, the tape counter or
current time are shown. The display can be selected
with the [CNT/TIME] button.
• When the power is turned off, the present time (hour,
minute, second) is shown.
Recording/playback mode time display
• Shows the recording/playback mode set with the [TIME
MODE] button.
• When a tape ends in the Record mode, the record time
mode indication goes out and the "End" indication
blinks (when the <REC REMAIN> menu switch is set
to "OFF"). If the <REC REMAIN> menu switch is set
to "180S" or "360S", the "End" indication blinks
3 minutes or 6 minutes before the tape ends.
• When an problem occurs, the error indication
“E-
∗∗”
blinks. For details, refer to page 43.
• During the index search by RS-232C Command, the
index number is indicated in 2 digits (00-99). During
the index search by FF/REW Button, the index number
indicates 01 and 00 only.
11
CAM SW
OUT
ALARM
IN
COM
COM
ALARM
REC OUT
SERIES/CLOCK
ALARM
RESET
TAPE
END OUT
WARNING
/REC
OUT
IN OUT
8
7
1
2
3
4
6
5
VIDEO
AUDIO
IN IN
OUT
OUT
REMOTE
MIC
IN
CAM SW
OUT
ALARM
IN
COM
COM
ALARM
REC OUT
SERIES/CLOCK
ALARM
RESET
TAPE
END OUT
WARNING
/REC
OUT
IN OUT
2-1 FRONT PANEL
2-3 Rear Panel
2 CONTROLS AND CONNECTORS
Power cable
Connect the power plug to an AC 220-240 V, 50/60 Hz
outlet.
[MIC IN] mic input connector
Connect a microphone with 3.6-mm dia. plug. When
signals are input from both the microphone connector
and the audio input connector, audio signals are mixed
and recorded.
[VIDEO IN] video input connector (BNC)
Receives composite video signals from a connected
camera or other video source.
[AUDIO IN] audio input connector (RCA)
Receives audio signals from a connected audio source.
[AUDIO OUT] audio output connector (RCA)
Outputs audio signals.
[VIDEO OUT] video output connector (BNC)
Outputs composite video signals. Input camera signals
(composite video signals) can still be output through this
connector even when no power is supplied to the unit
(Power-Off Video Throughput function).
[REMOTE] remote connector (RCA)
Connect the optional RM-G30U remote control.
[SERIES/CLOCK OUT] series recording signal/clock
reset signal output terminal
Outputs the series recording signals or clock reset
signals.
Select the output signal with the <TERMINAL SEL 1>
menu switch.
• Series recording signal output
When the <TERMINAL SEL 1> menu switch is set to
“SERIES”, the series recording signal is output.
• Connect to the other VCR series recording signal input
terminal. When the tape being recorded in this unit
ends, a signal is output from this terminal to the
connected VCR.
• Select the signal output timing with the <REC
REMAIN> menu switch (tape end, or 3 minutes or 6
minutes before the tape ends).
• Clock reset signal output
When the <TERMINAL SEL 1> menu switch is set to
“C.ADJ”, the clock reset signal is output when the
internal clock is at AM0:00 and PM0:00. When
connected to the [CLOCK IN] terminal of another SR-
L910E/EK, this unit
’s time can be synchronised with
the time on the other VCR if the time difference is
within ±30 seconds.
Connecting the wires to the terminals
button
1. Hold the button down
and insert the wire
over the top of the
terminal.
2. Release the button to
lock the wire in the
terminal.