Filter
Top Products
EN 47
LOCATE EDIT-IN POINT
8
Find the point on the source
tape from where you want
the edited scene to begin by
pressing PUSH JOG
@ #
or
using the TIME SCAN
SHUTTLE ring or the JOG
dial, then press PROG.
● The edit-in point is
registered in memory
and appears on the screen.
LOCATE EDIT-OUT POINT
9
Find the point where you
want the edited scene to
end by pressing PUSH
JOG
@ #
or using the TIME
SCAN SHUTTLE ring or
the JOG dial, then press
PROG.
● The edit-out point is
registered in memory
and appears on the
screen.
● The total time of the
edited scenes is displayed
to the right of "(+)".
● Repeat steps 8 and 9 for
each additional scene.
PREPARE RECORDING DECK
10
Engage its Record-Standby mode.
START R.A. EDIT
11
Press OK.
● Automatic editing begins; all the specified scenes are
copied to the recording deck in the order they were
registered.
● The on-screen display remains while your recorder
searches for each scene (blinking cursor indicates
scene currently being searched for), but disappears
during actual editing.
● During scene search, the recording deck automati-
cally enters its Record-Standby mode.
● When all registered scenes have been edited, your
recorder enters the Pause mode, the recording deck
enters its Record-Standby mode, and the cursor blinks
at the next available number.
END R.A. EDIT
12
Press MENU to return to the normal screen, and engage
the Stop mode for your recorder and for the recording
deck.
To Make Corrections . . .
. . . during step 8 or 9, you can cancel registered in and out
points by pressing CANCEL on the remote control. Each time
you press, the preceding point is erased.
● If, for example, you have registered 5 sets of in and out points
and want to reset the first set, you have to press CANCEL until
all points after the first set have been erased. Reenter them
after you've repaired the first set of points.
Memory Capacity
Random Assemble Editing shares
memory space with the recorder's
timer. If there are programs
occupied by timer-recording data,
those spaces cannot be used to
register edit-in and -out points —
meaning you won't be able to edit
8 scenes.
● When all 8 programs are full,
"PROGRAM FULL" appears on
the R.A. EDIT screen.
● To cancel a program, see page 34.
RM-V700U Multi-Brand R.A. Edit Controller
(Not provided)
By connecting this controller to your recorder's R.A. EDIT
connector, you can perform Random Assemble Editing in
combination with a second non-JVC video recorder. The controller
is compatible with various major recorder brands. For compatible
systems and availability, please consult your JVC dealer.
NOTE:
Although the RM-V700U is designed to operate the recording
deck, it may not work with some recorders, or may have limited
function capability.
NOTES:
●
You can also monitor the sound when searching for scenes
you want to edit in steps 8 – 9. Since you can hear the
soundtrack during selection, you can avoid abrupt or
unnatural sounding scene-to-scene transitions. The sound that
is heard, however, is not TimeScan Audio.
●
When editing, there may be a discrepancy of about 2 seconds on
the source tape between the locations you chose as edit-in/-out
points and the locations your recorder recognises as those points.
●
For any scene, the edit-out point must have a counter reading
that is at least 1 second after the corresponding edit-in point. Any
less than 1 second and the edit-out point will not be registered.
●
Since the source recorder prerolls during Random Assemble
Editing, there must be at least 15 seconds worth of recorded
material prior to any edit-in point on the source tape.
●
If the search time for an edit-in point exceeds 5 minutes, the
recording deck enters its Stop mode and editing will not take place.
●
During steps 8 and 9 — if you engage the Pause mode while
registering edit-in and -out points in the R.A. Edit screen, the
characters in the on-screen display may become distorted. This
is normal.
=1
2
3
4
5
6
7
8
– 0:00:00 (+) 0:00:00
[PROG] =
=1 0:02:23
2
3
4
5
6
7
8
0:02:23 (+) 0:00:00
[PROG] =
=1 0:02:23 0:02:51
2
3
4
5
6
7
8
0:02:51 (+) 0:00:28
[PROG] =
PROGRAM FULL
– 0:00:00 (+) 0:00:00
[MENU] : EXIT