Filter
Top Products
10 EN
Functional overview (cont’d)
Before you start
Using a remote control
Keep in mind the following when using the remote
control:
• Make sure that there is no obstacle between the
remote control and the remote sensor on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the
remote sensor of the unit.
• Remote control for different devices can interfere
with each other. Avoid using remote control for
other equipment located close to the unit.
• Replace the batteries when you notice a fall off in
the operating range of the remote control.
• The maximum operable ranges from the unit are
as follows.
-
Line of sight: approx. 23 feet (7m)
-
Either side of the center:
approx. 16 feet (5m) within 30°
-
Above: approx. 16 feet (5m) within 15°
-
Below: approx. 10 feet (3m) within 30°
Installing batteries in the remote control
Install two “AAA” size batteries (supplied) matching
the polarity indicated inside battery compartment of
the remote control.
Note:
Incorrect use of batteries can result in hazards
such as leakage and bursting. Please observe the
following:
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together,
although they may look similar, different batteries
may have different voltages.
• Make sure that the plus and minus ends of
each battery match the indications in the battery
compartment.
• Remove batteries from equipment that is not going
to be used for a month or more.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or
disassemble batteries.
P
O
W
E
R
O
N
S
T
A
N
D
B
Y
-
O
N
R
E
W
F
.
F
W
D
S
T
O
P
/
E
J
E
C
T
P
L
A
Y
R
E
C
O
R
D
C
H
A
N
N
E
L
D
.
D
U
B
B
I
N
G
O
P
E
N
/
C
L
O
S
E
V
C
R
S
O
U
R
C
E
D
V
D
S
T
O
P
P
L
A
Y
R
E
C
O
R
D
S
-
V
I
D
E
O
V
I
D
E
O
L
A
U
D
IO
R
I
R
Remote
control
Within about
23 feet (7m)
30°
30°
2
1
3
Because this product is a combination of a VCR and a DVD recorder, you must select first which component
you wish to operate with [SOURCE].
POWER ON
STANDBY-ON
REW F.FWD STOP/EJECT PLAY RECORD CHANNEL D.DUBBING
OPEN/CLOSE
VCRSOURCEDVD STOP PLAY RECORD
S-VIDEO VIDEO
L AUDIO R
IR
VCR SOURCE DVD
DVD indicator
VCR indicator
SOURCE button
VCR button
DVD button
STANDBY-ON
OPEN/CLOSEVIDEO/TV VCR
.@/:
GHI
PQRS TUV WXYZ
JKL MNO
ABC DEF
DVD
DISPLAY
SETUP
OK
0
21
4
65
3
9
7
8
CHANNEL
TIMER
TIMER SET
SEARCH AUDIO DUBBING
SLOW
CM SKIP
RAPID PLAY
VCR REC DVD REC REC MODE
DISC MENU
RETURN
CLEAR/C-RESET TITLESPACE
Press [VCR] on the remote control.
(Verify that the VCR indicator is lit.)
Press [DVD] on the remote control.
(Verify that the DVD indicator is lit.)
The VCR/DVD recorder switching
Note:
• Pressing only [SOURCE] on the front panel
DOES NOT switch the mode of the remote
control. You MUST select the correct mode on
the remote control.
• You cannot switch to another mode (DVD or
VCR) during in the timer-standby mode.
• Pressing
[DVD REC I] or [VCR REC I] on the
remote control switches immediately its respective
mode so that you can start recording directly on
the appropriate media.
VCR MODE
DVD MODE
E9A80UD_MWR20V6_01.indd 10 2006/01/18 11:45:16