Filter
Top Products
15
EDITING TP IN CHANNEL SEARCH MENU
Press MENU, go to INSTALL and select Channel Search. Configure following items.
Adding TP
Satellite: Press OK and select satellite. Press right key and go to Scan Mode and select
Manual TP / All Ch. TP Data will open. Press left / right and select User TP 1. Enter,
Frequency, Polarity and S/R. Press EXIT and TP Data will close. Added TP is already
selected for channel search. Press blue key. After tuning it will store the TP. To add
another TP select User TP 2.
Editing TP
Same as adding but select the required TP and edit its data.
TROUBLE SHOOTING GUIDE
If you suspect there is a problem with your STB, please check the following.
WARNING! Do not attempt to repair the STB yourself. Tampering with the receiver may
result in fatal electric shock and will invalidate your warranty.
Front display not lit --- Check power lead is connected and the power is on.
No picture or sound --- Check TV is tuned for correct UHF channel or is switched to
correct AV input. Channel is scrambled.
No signal --- Check antenna position. Check LNB wire is not damaged or shorting. Check
LNB may be faulty. Unplug receiver from power socket and retry.
Interference, on picture, using UHF output --- Local terrestrial channel interference.
Change UHF output channel to different one and re-tune your TV. Select the appropriate
‘TV Standard’ using TV Settings menu.
Picture with blocking or frozen --- Signal is weak. Check signal & quality in Channel
Search menu. Check antenna position.
Remote control not working --- Check the batteries and replace with new. Check front
panel of STB is not obstructed.
You have lost or forgotten your password --- Apply master password or contact your
Manhattan dealer.
GENERAL SPECIFICATIONS
Conditional Access Interface
Smart Card Reader 2 Embedded Card Slots
PCMCIA 1 Common Interface (CI) Slot
Digital Tuner & Demodulator
Input Connector F-Type, IEC, 169-24, Female
Input Frequency & Loop
through range
950 MHz to 2150 MHz
Input Impedance 75 ohm unbalanced
Signal Level -25 to –65 dBm
16
LNB Power & Polarization Vertical + 13V, Horizontal + 18V, Max Current 500 mA,
Short Circuit Protection
22KHz Tone Frequency 22 KHz +/- 2 KHz, Amplitude 0.7 +/- 0.2V
DiSEqC Control Version 1.0, 1.2 & USALS
Demodulation QPSK
Input Symbol Rate 1-45 Ms/s, SCPC & MCPC
FEC Decoder Convolutional Code Rate, 1/2, 2/3, 3/4, 5/6 and 7/8
with constraint length K=7
System Memory
Main Core Processor ST-5119 @ 200 MHz
Flash Memory 2MB
SDRAM 16MB
EEPROM 8KB
Channel Memory 6000 Channels
Language Menu English, French, German, Spanish, Italian, Portuguese,
Danish, Swedish, Norwegian, Finish, Polish, Russian,
Greek, Turkish, Farsi & Arabic
MPEG Transport Stream, A/V Decoding
Transport Stream MPEG-2 ISO/IEC 13818
Profile Level Transport Stream Specification MPEG-2 MP@ML
Input Rate Max. 90 Mbit/s
Aspect Ratio 4:3 Letter Box, 4:3 Pan & Scan, 16:9 Wide
Video Resolution 720X576 @ 25Hz, 720X480 @ 30Hz
Audio Decoding MPEG/Musicam Layer I & II
Audio Mode Single Channel, Dual Channel, Joint Stereo & Stereo
Sampling Rate 16, 22.05, 24, 32, 44.1 and 48 KHz
Digital Audio S/PDIF
A/V & Data In / Out
TV SCART Video Output (CVBS, RGB). Audio output with Volume
Control (Resolution: 20 bits DAC, Max 2Vrms)
VCR SCART Video Output (CVBS) Video Input (CVBS) Audio Output
(Resolution: 20bits DAC Max.1Vrms)
Video RCA / Cinch, Video Output (CVBS)
Audio R/L RCA/Cinch Volume & Mute Control
S/PDIF Digital audio Output, RCA (Resolution: 20 bits)
RS-232 Transfer rate 115.2 Kbps 9 Pin D-sub type
RF-Modulator (OPTIONAL)
RF-Connector 75 Ohm, IEC 169-2 Male/Female
Frequency 470 to 850 MHz
Output Channel CH 21 – 69 for the re-modulator
Multi TV Standards PAL G, I, K, M & NTSC M
Preset Channel CH 64 (software changeable by Menu)
Power Supply
Input Voltage 90 to 240 VAC, 50/60 Hz
Type SMPS
Power Consumption Max 25W
Standby 7.2W