Mitsubishi Electronics WD-62827 Projection Television User Manual


  Open as PDF
of 128
 
Chapter 2. Connecting 25
Connecting a VCR to an Antenna or Wall Outlet Cable
Connecting VCR Audio and Video to the TV
VCR to an Antenna or Wall Outlet
Cable (Audio & Video)
Figure 5
A two-way RF splitter, 3 coaxial cables, right and left audio
cables, and an S-video or video cable are required. These are
not included with the TV but are available at most electronics
stores.
1. Connect the incoming cable or Antenna to IN on the
RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the VCR back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel. This
connection also allows you to use the TV Guide On
Screen® feature.
4. To use the TV speakers with the VCR, connect a set
of audio cables from AUDIO OUT on the VCR back
panel to INPUT-1 AUDIO-LEFT (MONO) and AUDIO-
RIGHT on the TV back panel. The red cable connects
to the R (right) channel and the white cable connects
to the L (left) channel. If your VCR is mono (non-
stereo), connect only the white (left) cable.
Figure 5. Connecting a VCR to an Antenna or Wall Outlet Cable
5. Connect either an S-Video or Video cable from
VIDEO OUT on the VCR back panel to INPUT-1
VIDEO on the TV back panel. Only one type of
video cable should be connected. S-Video is
recommended, if available.
6. For NetCommand®-controlled recordings (including
TV Guide On Screen), connect a set of audio cables
from AUDIO IN on the VCR back panel to RECORD
OUTPUT/AUDIO-LEFT and AUDIO-RIGHT on the TV
back panel. The red cable connects to the R (right)
channel and the white cable connects to the L (left)
channel.
7. Complete the NetCommand controlled recordings
connections by connecting a Video cable from
VIDEO IN on the VCR back panel to RECORD
OUTPUT/VIDEO on the TV back panel.
$0.10/&/5
:1C1SJQQJ
*/165
47*%&0
7*%&0
"6%*0
-&'5
.0/0
"6%*0
3*()5
%57$"#-&
7)'6)'
%*(*5"-
"6%*0
065165
$BCMF$"3%
64&8*5)
"/5$"3%501
2
:
1C
1S
"6%*0
-&'5
.0/0
"6%*0
3*()5
065165
"6%*0
065165
3&$03%
065165
%7*
"OBMPH"VEJP
7*%&0
AUDIO-
LEFT/
(MONO)
"6%*0
3*()5
*&&&
*/165
065165
/FU$PNNBOE
*3&.*55&3
¸
(-JOL
¸
*/165
1$'03)%.*
0/-:)[
7("87("
47("847("
9("9
64&8*5)
$BCMF$"3%
"/5."*/"/5"69
.0/*503-*/,
$0/530-34$
$0.10/&/5
:1C1S
JQQJ
%57$"#-&
7)'6)'
%*(*5"-
"6%*0
065165
2
:
1C
1S
"6%*0
-&'5
.0/0
"6%*0
3*()5
065165
"6%*0
065165
%7*
"OBMPH"VEJP
/FU$PNNBOE
*3&.*55&3
¸
(-JOL
¸
(-JOL
¸
(-JOL
*/165
1$'03)%.*
64&8*5)
$BCMF$"3%
"/5"69
$BCMF$"3%
64&8*5)
"/5$"3%501
*&&&
*/165
065165
1$'03)%.*
0/-:)[
7("87("
47("847("
9("9
.0/*503-*/,
$0/530-34$
"/5&//"
065
065
065
065
*/
*/
*/
*/
3
3
-
-.0/0
"6%*0
7*%&0
47*%&0


*/
065
065
5808":41-*55&3


*ODPNJOH
$BCMF
3'4QMJUUFS

7$3CBDLQBOFM








*GZPVS7$3IBTBWJEFP
DIBOOFMPS3'0/0''
TXJUDITFUJUUP0''
"UUBDIPOMZPOFUZQFPG
WJEFPDBCMF4WJEFP
SFDPNNFOEFEJG
BWBJMBCMF
7JEFPDBCMF
DPNQPTJUFWJEFP
4WJEFPDBCMF
57CBDLQBOFM
Note:
NetCommand® will assume your VCR is connected
to inputs as shown on this page. If you use any other
inputs for your VCR or add a second VCR, this change
must match in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.
 previous next