A SERVICE OF

logo

Open as PDF
next previous
28
Chapter 2. Connecting
A/V Receiver (Stereo System)
Figure 7
A coaxial digital audio cable or stereo audio cables are required.
These cables are not provided with the TV.
• To connect an analog A/V receiver:
Connect a set of stereo audio cables from OUTPUT
AUDIO 2 on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. The red cable
connects to the R (right) channel and the white cable
connects to the L (left) channel.
• To connect a digital A/V receiver with Dolby®
Digital surround sound:
Connect one end of a digital audio cable to DIGITAL
AUDIO on the back of the TV. Connect the other end
to the COAXIAL DIGITAL INPUT on the back of the
A/V receiver.
"73FDFJWFS3FBS1BOFM

57CBDLQBOFM
*/
57
-
3
*/165
$0"9*"-

3FE
8IJUF

INPUT
1
2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DIGITAL
AUDIO
OUTPUT
CableCARD™
USE WITH ANT 1 CARD TOP
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
OUTPUT
AUDIO
OUTPUT
RECORD
OUTPUT
DVI
Analog Audio
12
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
VICE
MONIT
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1
EE 1394
NPUT/
UTPUT
',INK
¸
INPUT
CableCARD
ANT 1 / MAIN
ANT 2 / AUX
Q
INPUT
1
2
S
-
V
I
D
E
O
O
VIDE
O
AU
DI
O
-
LEFT
/
(
M
O
N
O)
A
U
DI
O-
R
I
G
H
T
C
a
b
l
e
C
A
C
C
R
D
™
U
S
E
W
I
T
H
A
N
T
1
C
A
C
C
R
D
T
O
P
Y
P
b
Pr
A
UDIO
-
L
EFT
/
(
MONO
)
AUDIO-
R
IGH
T
DVI
A
na
l
og
A
u
dio
1
2
V
I
CE
MO
NI
T
VIDEO 480i/480
p
/720
p
/1080
i
AUDI
O
P
C
M LINEAR
1
E
E
1
3
9
4
4
4
9
9
N
P
U
T
/
TT
U
T
PU
T
T
T
INPU
T
'
,IN
K
¸
CableCARD
A
NT 1
/
MAIN
ANT 2
/
A
U
X
3FE
8IJUF

6TFJG
DPOOFDUJOH
BOBOBMPH
"7SFDFJWFS
6TFJG
DPOOFDUJOHB
%PMCZEJHJUBM
"7SFDFJWFS
Figure 7. Connecting an A/V receiver
Connecting an A/V Receiver (Stereo System)
Connecting a Satellite Receiver or Other Device with S -Video
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 VIDEO on the
TV back panel.
2. Connect a set of audio cables from AUDIO OUT on the
satellite receiver back panel to INPUT-2 AUDIO, on the
TV back panel. The red cable connects to the R (right)
channel and the white cable connects to the L (left)
channel.
Note: Refer to the Satellite Receiver Owner’s Guide
for Dish Antenna connections.

57CBDLQBOFMTFDUJPO

:$
-
3
-
3
7*%&0065
"6%*0065
"6%*0*/
8IJUF
3FE
3


3FE
8IJUF
BOZ4WJEFPEFWJDF
INPUT
1
2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
Note: NetCommand® will assume you
connected your Satellite Receiver to Input-2. If
you add a second Satellite Receiver or use any
other inputs for your Satellite Receiver, this
change must match in the NetCommand system.
See Editing NetCommand Setup in Chapter 3 for
more information.
Figure 8. Connecting a Satellite Receiver with S-Video
Note: On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from the TV
as a digital signal. This is not anticipated to be a
common situation. To hear these copy-protected
signals through the A/V receiver, use connections
for analog A/V receivers.