Filter
Top Products
En-23
Option1 Settings Menu
Setting the on-screen menu
This sets the position of the menu, the display format
(horizontal or vertical) etc.
Example: Turning the DISPLAY OSM off
On “OPTION1” menu, select “OSM”, then press the MENU/
ENTER button.
The “OSM” menu appears.
On “DISPLAY OSM” of “OSM” menu, select “OFF”.
SEL. ADJ. RETURN
OSM
EXIT
DISPLAY OSM
OSM ADJ.
OSM ANGLE
OSM ORBITER
OSM CONTRAST
: OFF
: 1
: H
: OFF
: LOW
Information
Ⅵ DISPLAY OSM settings
ON: The informations on screen size, volume control,
etc. will be shown.
OFF: The informations on screen size, volume control,
etc. will not be shown.
The DISPLAY button on the remote control will not
function either.
Ⅵ OSM ADJUST settings
Adjusts the position of the menu when it appears on
the screen.
The position can be set between 1 to 6.
Ⅵ OSM ANGLE settings
Sets the display format (landscape “H” or portrait “V”).
When the unit is installed vertically set the OSM
ANGLE at “V”.
“H”“V”
Ⅵ OSM ORBITER settings
ON: The position of the menu will be shifted by eight
dots each time OSM is displayed.
OFF: OSM will be displayed at the same position.
Ⅵ OSM CONTRAST settings
NORMAL: OSM brightness is set to normal.
LOW: OSM brightness is set to lower.
Setting the BNC input connector type
Select whether to set the input of the 5 BNC connectors to
RGB or Component.
Example: Set the BNC INPUT mode to “COMP.”
On “BNC INPUT” of “OPTION1” menu, select “COMP.”.
SEL. ADJ. RETURN
OPTION1 1 / 4
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
: AUTO
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
: COMP.
: RGB
: 1080B
: OFF
: OFF
EXIT
Information
Ⅵ BNC INPUT Settings
RGB: Use the 5BNC terminals for RGB input.
COMP.: Use the 3BNC terminals for component input.
SEL. RETURN
OPTION 1 1 / 4
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
: RGB
: RGB
: AUTO
: 1080B
: OFF
: OFF
EXIT
MENU/ENTER
OK
: RGB
: RGB
: AUTO
: 1080B
: OFF
: OFF
1024768
EXIT
SEL.
RETURN
MENU/ENTER
OK
OPTION1
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
HD SELECT
INPUT SKIP
ALL RESET
Checking the signal being transmitted to
RGB1 terminal
Use this to confirm the signal being transmitted to the
RGB1 terminal.
It is set to RGB and can not be adjusted.
CAN NOT ADJUST
OPTION1 1 / 4
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
: AUTO
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
: RGB
: RGB
: 1080B
: OFF
: OFF
Setting a computer image to the correct RGB
select screen
With the computer image, select the RGB Select mode
for a moving image such as (video) mode, wide mode or
digital broadcast.
Example: Setting the “RGB SELECT” mode to
“852ן480 ”
On “RGB SELECT” of “OPTION1” menu, select
“852ן480”.
SEL. ADJ. RETURN
OPTION1 1 / 4
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
: 852ן480
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
: RGB
: RGB
: 1080B
: OFF
: OFF
EXIT
Information
Ⅵ RGB SELECT modes
AUTO: Select the suitable mode for the specifications
of input signals as listed in the table “Computer input
signals supported by this system” on page En-40.
The others: The available resolutions are shown.
See page En-40 for the details of the above settings.