Filter
Top Products
49EN
Disc
Management
Recording
Playback
Introduction
Connections Basic Setup Editing
Function
Setup
VCR Functions Others Español
TIMER RECORDING
Hints for Timer Recording
The Priority of Overlapped Settings
Note for DVD recording
• When the recording time of 2 programs are overlapped, or
the end time of a program and the start time of another
program is the same, the first 2 minutes (at the longest) of
the subsequent program will be cut off.
• If the cut-off portion comes up to 3 minute or more, this
program will be displayed with error number E40 in the
timer programming list.
PROG. A
PROG. B
actual
recording
The first 2 minutes (at the longest) will be cut off.
PROG. BPROG. A
When the end time of the programming
currently being recorded and the start time
of the subsequent program are same:
The beginning of the PROG. B may be cut off.
When the starting time is the same:
A program set previously (PROG. A) has priority.
PROG. A
PROG. B
actual
recording
PROG. A
PROG. B
The rst 2 minutes (at the longest) will be cut o.
PROG. A
• Timer program which has the earlier start time will be placed first in the timer program list, and be given priority over
the programs with the later start time when timer programs overlap.
• When timer programs overlap, the first 2 minutes (at the longest) of the later recording will be cut off.
• When 2 or more timer programs have the same start time, the program set first will be given priority.
• A timer recording of lower priority will be canceled or start from the middle.
• Check the overlapped timer programmings and change the priority if necessary.
• If there is a power failure or this unit has been
unplugged for more than 30 seconds, the clock setting
and all timer programming will be lost.
• If a disc is not inserted, "DVD" on the front panel display
flashes and timer recording cannot be performed. In some
cases, will appear momentarily around the start point as
the unit attempts to record. Please insert a recordable disc.
• If a cassette tape with an erase-protection tab is not in
the cassette compartment or there is no cassette tape in
the cassette compartment, “VCR” on the front panel
display flashes and timer recording cannot be
performed. Please insert a recordable cassette tape.
• If you press [T-SET] and turn on the unit while either
DVD or VCR is in timer standby mode,
disappears. In
this case, you cannot change the mode between DVD
and VCR. You cannot change any settings using [SETUP]
or edit discs.
• When all the timer recording is completed,
flashes. To
play back or eject the recorded disc, press [T-SET] first,
then select the recorded title and press [PLAY B], or
[OPEN/CLOSE A] to remove the disc.
• If both DVD and VCR are timer programmed, you cannot
use any functions for either unit during timer standby or
timer recording. If you want to use functions other than
recording under such condition, cancel timer recording
by pressing [T-SET] during timer standby or stop
recording by pressing [STOP C] on the front panel
during timer recording.
• To cancel the timer standby mode, press [T-SET].
• When the starting and the ending time are the same, the
length of the recording will be set for 24 hours. When
the disc or cassette tape becomes full during the
recording, the unit turns itself off.
• When the programmed starting and ending time are
earlier than the current time, the setting will not be
accepted and be cleared for redoing.
• If the starting time is earlier and the ending time is later
than the current time, the recording will start right after
you turn the power off.
• The timer recording for digital TV cannot record any
audio language other than English.
• The timer recording cannot be performed in DVD and
VCR at the same time. If you set 2 programming with the
same channel and time in both devices, the program
with a lower program number will be recorded.
• The timer recording for digital TV cannot record any
audio language other than English.
E9H10UD.indd 49E9H10UD.indd 49 2007/02/19 14:55:352007/02/19 14:55:35