Filter
Top Products
23
Convenient Automatic Functions
VCR Auto Power On
When you insert a video cassette, the VCR switches on
automatically.
Auto Playback Start
When you insert a video cassette with a broken erasure
prevention tab, playback start automatically without having to
press the [Play] (26).
VCR-off Playback
When the VCR is off, an inserted cassette can be played
back by pressing the [Play] (26).
Auto Rewind
When the tape reaches the end, the VCR automatically
rewinds it to the beginning.
• This function does not work during timer recording and
OTR.
Automatic Switching Off and Ejection
When the VCR is switched off, and inserted cassette can be
ejected simply by pressing the [EJECT] (42).
The VCR will eject the cassette and automatically turn itself
off again.
VCR-off Search
When the VCR is off, the VCR starts Intro-Jet Scan of an
inserted cassette by pressing the [LIBRARY/SEARCH] (4).
Adjusting the Playback Picture
Under normal conditions, the VCR automatically adjusts the
playback picture for optimum quality. However, in some
cases it may be necessary to adjust it manually.
If noise bars appear during normal playback, slow playback
or still playback, follow the operations below.
During normal or slow playback,
press the [TRACKING/V-LOCK]
(33) I (s) or J (r) until the bars
noise disappear.
• If the noise bars appear during still
playback, switch the VCR over to
the slow playback mode and then
adjust the tracking as explained
above.
Press the [TRACKING/V-LOCK] (33) I (s) and J (r)
simultaneously to return to Auto Tracking.
If the still picture scrolls up or down, perform the following
operation.
During still playback, keep the [TRACKING/V-LOCK] (33)
I (s) or J (r) pressed until the picture stops scrolling.
Precautions:
• With certain TV models and tapes, it may not be possible to adjust
the tracking.
• If you play back a cassette that was recorded on another unit of
VCR, the picture quality may be inferior in the normal playback,
slow playback, and still playback, and it may need to manual adjust
the tracking by above method. Also, on some TVs, the picture may
scroll up and down in the special playback functions.
However, these are not malfunctions.
Before Requesting Service
On Screen Display Messages
The error messages are given in brackets [ ].
[Please insert video tape!]
• You pressed the [REC] (28), [REC/OTR] (51), the
[DIRECT TV REC] (36), the [Play] (26), the [Fast Forward]
(25), the [Rewind] (8) or the [LIBRARY/SEARCH] (4)
when no cassette was inserted in the VCR.
You pressed the [TIMER] (20) when no cassette was
inserted in the VCR with a timer recording programmed.
Insert a video cassette.
[Please use tape with unbroken recording tab !]
• You pressed the [REC] (28), [REC/OTR] (51) or the
[DIRECT TV REC] (36) when a cassette with a broken out
erasure prevention tab was inserted in the VCR.
You pressed the [TIMER] (20) when a cassette with a
broken out erasure prevention tab was inserted in the VCR
with a timer recording programmed.
Insert a video cassette with an intact erasure prevention tab
on which recording is possible.
[This action is not possible before time and date are set]
• You pressed the [SV/V+] ([ShowView]) (30) or the [PROG./
CHECK] (14), even though the time and date have not yet
been set on the VCR.
Set the time and date.
[No timer programmes to be done!]
• You pressed the [TIMER] (20) even though no timer
recording has been programmed.
Programme a timer recording before pressing the [TIMER]
(20).
[Please put VCR into stop mode first]
• You attempted to change the contents of the timer
programming while a timer recording was being performed.
Put the VCR into the stop mode first.
Other messages may also appear.
Follow the instructions given on the TV screen.
TV screen
Playback picture
containing noise bars