Filter
Top Products
7
If you are connecting your VCR to a TV using RF coaxial
cable and 21-pin Scart cable, then follow the steps.
(AV Connection)
RF Coaxial cable must be connected to watch TV channels
even if 21-pin Scart cable is used to connect VCR to TV.
Hint:
• If the TV set is equipped with a 21-pin Scart socket that features
Y/C signal separation, set the [Normal/S-Video Output] switch on
the rear panel to [S-VIDEO OUT] so that you can play back with
high picture quality and use a fully-wired
21-pin Scart cable
(not supplied) to connect the VCR to the TV.
If you are connecting your VCR to a TV using S-Video cable,
then follow the steps. (S-Video Connection)
RF Coaxial cable must be connected to watch TV channels.
Auto Setup Function
The Auto Setup function automatically tunes all available TV
stations and sets the VCR’s clock to the current date and
time.
1) Press the [VCR-ON/OFF] (1) to
turn on the VCR.
The Country setting menu
appears on the TV screen.
2) Press the [Cursor] (38) 3421.
Select the country where you are
using the VCR.
3) Press the [OK] (24).
The VCR’s Auto Setup
automatically starts and tunes all
available TV stations and also
sets the clock. This takes about 5
minutes.
When the indication appears on
the VCR display, the Auto Setup
is complete.
4) Press the [MENU] (7) for more
than 5 seconds.
The RF output channel number appears on the VCR
display.
The initial setting is channel 36.
5) Press the [Numeric] (2) [0].
The displayed RF output channel number changes to
[– –].
6) Press the [OK] (24) to conclude the setting.
To cancel the Auto Setup before it has finished
Press the [EXIT] (27).
When the clock setting menu appears after Auto Setup
has finished
1) Press the [Cursor] (38) 3421 to set the correct time
and date.
2) Press the [OK] (24) to conclude the setting.
To confirm that the TV stations have been tuned
correctly by the Auto Setup function
See page 18.
When no station has been set, confirm all connections
of the VCR again and restart the Auto Setup
See page 19.
When the station names and/or channel numbers have
not been set correctly
See page 18.
Hint:
• If you select [Schweiz], [Suisse] or [Svizzera] on the Country
setting menu, the other setting menu appears automatically to let
you set [Power save] to [ON]. In this setting, the VCR’s power
consumption is minimised when it is off (Standby mode). To turn
the VCR on, keep the [VCR-ON/OFF] (1) pressed on the VCR
main unit, not with the remote control.
(continues on the next page)
1 2
3
4
5
6
7
8
9
10
11
1 AV1 21-pin Scart socket
2 Normal/S-Video Output
3 Aerial Input socket
4 Aerial Output socket
5 Aerial (not supplied)
6 Aerial lead (not supplied)
7 TV (not supplied)
8 Aerial Input socket
9 21-pin Scart socket
10 RF Coaxial cable (supplied)
11 Fully-wired 21-pin Scart cable
(not supplied)
31
42
5
6
13
12
7
8
9
10
11
1 S-Video Output socket
2 Audio Output socket
3 Aerial Input socket
4 Aerial Output socket
5 Aerial (not supplied)
6 Aerial lead (not supplied)
7 TV with S-Video Input socket
(not supplied)
8 Aerial Input socket
9 S-Video Input socket
10 Audio Input socket
11 Audio cables (not supplied)
12 S-Video cable (not supplied)
13 RF Coaxial cable (supplied)
Country
Belgien
Belgique
België
Danmark
España
Ελλάδα
France
Italia
Nederland
Norge
Deutschland
Österreich
Portugal
Suomi
Sverige
Schweiz
Suisse
Svizzera
others
Panasonic VCR
Country
Tuning
: others
: Ch 21
Auto-Setup
Panasonic VCR