Filter
Top Products
Getting Started
11
Tuning the TV to Your Unit
The unit supplies a signal to the TV via the RF coaxial cable on channel
AU28s 69
or
NZ21s 69
. It is possible to view the unit’s picture on your TV in the
same way that you watch TV broadcasts. The unit is fitted with its own tuner (just like a normal TV) and can be preset to receive up to 99 TV broadcast stations.
≥Switch [VHS/TV/DVD] to “VHS”.
¬ If you have connected the unit to the TV through the audio/video output sockets
You do not need to follow the procedure below. To view the pictures from the unit, set to the AV mode on the TV with [AV].
The local TV broadcast channels 2, 7, 9, 10 and 28 are factory-preset in the unit.
That is, if you can receive TV broadcasts on VHF channels 2, 7, 9, 10 and UHF channel 28, these are
already tuned on the programme positions with the matching numbers.
[1] Press [VHSÍ] to turn on this unit.
[2] Hold down [MENU] for 5 seconds or more.
[3] Set the TV to an unused position for the unit
viewing channel.
≥Tune the TV until the display shown on the right appears. Refer also
to the TV’s instructions regarding tuning.
[4] Press [MENU].
When the unit is turned on after connecting the aerial cable and the
mains lead for the first time, tuning starts automatically.
≥If the unit is turned on with the aerial not connected, all channels are skipped.
[1] Press [VHSÍ] to turn on this unit.
[2] Set the TV to an unused position for the unit
viewing channel.
≥Tune the TV until the display shown on the right appears. Refer also to
the TV’s instructions regarding tuning.
[3] Press [MENU].
¬ To cancel Auto Tuning partway through
Press [MENU]. Auto Tuning will stop halfway by turning the unit off, pressing [MENU], playback or a
power failure.
¬ If Auto Tuning stops halfway by turning the unit off, playback or a power failure
≥Disconnect the mains lead and then reconnect it.
≥Turn on the unit. Plug in Auto Tuning restarts.
¬ To set the channels manually (lpage 23)
ªTo restart Plug in Auto Tuning
≥Turn the unit on.
≥Make sure there is no video cassette in the unit.
1) Keep both [CH]
I
and
J
on the unit pressed simultaneously for 3
seconds or more until the channel on the unit’s display changes to 1.
2) Disconnect the mains lead and then reconnect it.
3) Turn on the unit. Plug in Auto Tuning restarts.
You can change the RF output channel, for example, when interference occurs
on the picture after tuning.
1) Hold down [MENU] for 5 seconds or more.
2) Press [CH]
IJ
to select the channel (AU28s69, NZ21s69).
≥Each time you press [CH]
IJ
(l left)
≥Set to “ss” (RF OFF) when you use the audio/video cable for the
connection.
≥You can also use the numeric buttons.
Example: “28”; [2]l[8]
3) Retune your TV to the new RF channel for the unit.
4) Press [MENU] to exit the setting mode.
Note:
≥Even if the RF output channel has been changed, it is not necessary to
perform Auto Tuning.
REW
FF
PULL
-
OPEN
/ I
EJECT
TIMER REC
TAPE REFRESH
AV2 IN
REC/OTR
CH
VIDEO
AUDIO
L
R
CH
VHS/DVD/TV
VHS/DVD
QUICK REPLAY DUBBING
REC
CH
VOLUME
TV
TV
VHS DVD
123
789
0
4
5
6
SLOW/SEARCH
NAVI
TOP MENU
MENU
RETURN
PROG/CHECK
PROG PLAY
DISPLAY
JET REW
TIMER
ENTER
PLAY
LIST
INDEX/SKIP
OUTPUT
TRACKING/V-LOCK
AV
DIRECT
NAVIGATOR
VHS/DVD
-/-
-
CH
VHS
MENU
VHS/
TV/
DVD
AV
Numeric
buttons
Pre-programmed TV Channels (for NV-VP31GL/Australia)
Plug in Auto Tuning (for NV-HV60GN/New Zealand)
Panasonic
END: MENU
CH 22 SEARCH
END: MENU
21
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
END: MENU
AUTO TUNING IS
COMPLETED.
Disappears 1
To change the RF output channel
Panasonic
END: MENU
NV-VP31GL
NV-VP31GN
28
…
69
(RF OFF)
NV-VP31GL
21
69
(RF OFF)
NV-VP31GN
VP31GL.book 11 ページ ２ ０ ０ ３年７月３ ０日 水曜日 午後８時２ ２分