Filter
Top Products
13
English
Programming a Recording (TIMER)VCR Manual Recording
Direct dubbing
Follow the steps below to copy a DVD or video disc to a
videotape.This will be possible only if the DVD is not copy
protected.
1 Put a videotape in the cassette compartment. Make sure the
tape’s record tab is intact and the tape is long enough to
record the disc.
2 Press VCR.
3 Select the recording speed.
Details are at “Selecting the recording speed (SP or LP)”.
4 Put the DVD you want to copy in the disc tray.
5 Press DVD.
6 Press PLAY B.While disc is playing, press PAUSE k at the
point you wish to start recording.
7 Press DIRECT DUBBING to record.
To pause the recording.
Press PAUSE k.
To r esume recording.
Press PAUSE k again.
To stop the recording.
Press STOP C.
Recording(From DVD To VCR)
1 Insert a DVD without copyright protection in the tray.
2 Insert a video cassette tape with its erase prevention tab in
place.
3 Select the recording speed.
Details are at “Selecting the recording speed (SP or LP)”.
4 Enter “004” with numerical key pads to appear “DISC” on the
TV screen.
5 Press REC I.
6 Change to DVD operation mode.
7 Press DVD, then PLAY B to begin the playback of a DVD.
8 Press VCR, then STOP C to stop recording.
General information
Use a TIMER programming to automatically start and stop a recording
at a later time or date.The System will switch to the right programme
number and begin recording at the correct time.With this System, you
can pre-programme up to eight recordings within a period of one
year.To make a programmed recording, your System needs to know:
* the date you want to make the recording
* the programme number of the TV channel
* the start and stop time of the recording
* VPS or PDC on or off
This information is saved in a TIMER block.
What is 'VPS/PDC'?
'VPS' (Video Programming System)/ 'PDC' (Programme Delivery
Control) are used to control the start and duration of TV channel
recordings. If a TV programme starts earlier or ends later than sched-
uled, the System will turn on and off at the correct time.
What do I need to know about 'VPS/PDC'?
Usually the VPS or PDC time is the same as the start time. But if
your TV guide shows a VPS or PDC time which is different from
the programme’s scheduled start time, e.g. 20.10 (VPS/PDC
20.14), you must enter the VPS/PDC time exact to the minute. If
you want a start time different from the VPS/PDC time, you must
switch VPS/PDC off.
Programming a recording
(with the 'SHOWVIEW® system')
You no longer need to tediously enter the date, programme
number, start and end time.All the information needed for pro-
gramming is contained in the SHOWVIEW-programming number.
You can find this SHOWVIEW number in most TV listing maga-
zines written next to the concerned programme.
1 Press SV/V+.
2 Enter the entire SHOWVIEW num-
ber.This number is up to 9 digits
long and can be found next to the
start time of the TV programme in
your TV listing magazine. [e.g: 1-
234-5 or 1 234 5]
If you make a mistake, you can
clear your input with CLEAR.
3 Press SV/V+.
4 Select ONCE, DAILY or WEEKLY
recording with K/L.Then press B.
R
ShowView system
ShowView No.
12345
– – – –
SET=SV/V+
CORRECT=CLEAR
END=EXIT
ShowView system
→ONCE
DAILY
WEEKLY
SELECT
KL CHOOSE B
END=EXIT
Selecting once/daily/weekly recordings
Using K/L, select from the following options:
'ONCE': Recording once
'DAILY': Repeated daily recordings (Monday to Friday)
'WEEKLY': Repeated weekly recordings (every week on the same
day)
'- -' appears at PROG..
* The programme number of the TV channel has not yet been
assigned to the SHOWVIEW number.Using the numerical key
pads, select the corresponding programme number (name) of
the TV channel.
The following message appears on the screen:'ERROR'
* The entered SHOWVIEW number is incorrect. Correct your input
or end with DISPLAY/STATUS/EXIT.
* Check the time/date (see chapter 'Installing your video',section
'Setting the time and date').
* A daily recording was entered for the wrong day. Daily pro-
gramming can only be used for recordings to be made from
Monday to Friday.
The following message appears on the screen:'TIMER
NOT COMPLETED'
* The channel is wrong.
E9015ED_EN.qx3 03.7.29 6:32 PM Page 13