Filter
Top Products
English
23
Operation with tape (Continued)
ShowView Programming
ShowView greatly simplifies entering the date, channel,
start and end times of a Timer Recording by simply
entering a ShowView Code. ShowView Codes are
published in most TV guide magazines; they can vary one
to nine numbers in length.
S
HOWVIEW is a registered trademark of Gemstar
Development Corporation.
The SHOWVIEW system is manufactured under licence
from Gemstar Development Corporation.
1
Make sure that TV channels have been tuned and stored
in correct SHOWVIEW order.
Insert a video cassette with protection tab into your
VCR.
2
Press SHOWVIEW.
3
Press D or E to select the recording type.
ONCE:To record once.
WEEKLY:To record at the same time every week.
DAILY:To record every day (except Saturday and
Sunday) at the same time.
4
Press the numbered buttons to enter the
ShowView Code of the TV programme that you wish
to record.
If you make a mistake press F then enter the revised
number.
5
Press OK.
If PLEASE CHECK is displayed it means that you have
entered the wrong ShowView number, entered the
ShowView number incorrectly.
If “- -” is displayed, you have to enter the programme
number of the station, you want to record from.
6
Press F or G to select the settings that you wish to
revise. (PR, DATE,TIME and SP).
Press
D or E to enter the correct information.
7
Press G to select the recording speed.
Press D or E to select the desired tape speed (SP, IP, or
LP).
IP mode determines how much tape is left and switches
speed from SP to LP, if necessary, to complete recording
the program.
Check that the timer event details are correct.
If you wish to record from AUDIO IN and VIDEO IN on
the front or from either of the EURO SCART sockets on
the back of VCR, press INPUT to select for correct
display (AV1,AV2 or AV3).
8
If you want to make another ShowView recording
repeat stages 2 - 7.
Press SYSTEM MENU twice.
If PLEASE CHECK is displayed, you have entered
incorrect information and will need to re-enter the data.
Press
11
to switch your VCR power off mode.
TIMER will appear in the video recorder’s display while
your VCR waits to make the recording.
To watch a DVD during timer recording standby mode,
press POWER and DVD to switch to DVD mode.
PR DATE TIME
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
10
PR-01
12
SP
11 11 55~::
i
PR DATE TIME
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
10
PR-01 12
SP
11 11 55~::
i
PR DATE TIME
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
10
PR-01
12
SP
11 11 55~::
i
ONCE
OK
i
0~9,
SHOWVIEW
246876543
REC
ONCE
OK
i
0~9,
SHOWVIEW
- - - - - - - - -
REC