Philips SRP5004/86 Universal Remote User Manual


  Open as PDF
of 17
 
10 EN 11EN
English
3.2 Learningbuttonfunctions
Ifyoumisscertainfunctionsfromyouroriginalremote
controlontheSRP5004,theSRP5004canlearnthese
functions.Youcanstoreafunctionunderanyofthe
availablebuttons,exceptunderthedeviceselectionbuttons
(
)andthe button.Anyfunctionalready
storedunderabuttonwillbedeleted.
TheSRP5004isequippedwithtwodedicatedbuttonsfor
learningadditionalfunctions:
and
.
Thesebuttonsdo
nothaveadefaultfunctionandenableyoutoaddextra
buttonfunctionswithoutdeletinganySRP5004functionality.
1
Makesurethatyouhavetheoriginalremotecontrolat
hand.
2 Selectthedesireddevice
(e.g.DVD).
Pressthe
deviceselectionbuttonto
selectDVD.
• Thebuttonlightsup.
3
Placebothremotecontrols
onaflatsurface(likea
table)andaimthem
head-to-headwithabout5
-10cminbetween.
4
Keepthe
button
and
thebutton
you
wishto
learnontheSRP5004(e.g.
the
button)pressed
simultaneously for 5 seconds,
untiltheredSetupLED
lightsup.
• Theremotecontrolisnowinlearnmode.
5
Pressand hold thebuttonthatyouwishtolearnonthe
originalremotecontroluntilthe
deviceselection
buttongivestwoshortblinksandbothbuttonandSetup
LED
gooutto confirm that learning was successful.
•
Theremotecontrolhasnowlearnedthenew
function.
Note
•
Itmayoccurthatlearningabuttonfunctionfailsthe
firsttime.Thedeviceselectionbuttonwillthengivea
longblinkandbothbuttonandSetupLED
will
go
out.Inthiscase,pleasetryagain.
•
Ifyoukeephavingtroublelearningbuttonfunctions,
checkthebatteriesinbothSRP5004andoriginal
remotecontrolandreplaceifnecessary.
•
Itmayalsobethattheremotecontrollearnmemory
isfull(atotalof60buttonscanbelearned).Inthis
caseyoucanr
esetoneormorebuttonstotheirall
originalfunctionsinordertocreatememoryspace.
Forthis,seechapter3.3.
3.3 Resettingabuttontoitsoriginalfunction
Ifanimprovedbutton(seechapter2.2.2)stilldoesnot
functionasexpected,youcanalwaysresetthebuttonto
itsoriginalfunction.Whenresettingabuttontoitsoriginal
function,anylearnedfunctionstoredunderthebuttonwill
bedeleted.
1
Inthecurrentdevice
mode,keepdigitbuttons 
and
pressed
simultaneously for 5 seconds,
untiltheredSetupLED
lightsup.
• Theremotecontrolisnowinsetupmode.
2
Pressdigitbuttons , ,
and ,
inthatorder.
• Aftereachbuttonpress
thedeviceselection
buttonblinksonce.
3
Pressthebuttonyouwish
toresettwice.E.g.the22
button.
• Aftereachbuttonpress
thedeviceselection
buttonblinksonce.
• Thedeviceselectionbuttonwillblinkonemoretime
toconfirmthatthebuttonwassuccesfullyresettoits
originalfunction.
• Thebuttoncannowalsolearnanewfunction,if
desired.
Usingtheuniversalremotecontrol
5sec.
5sec.
2x
 previous next