Filter
Top Products
12
3
DSP
In DSP mode you can select the equalizer settings POP M, JAZZ M,
CLASS M and FLAT M, and DSP OFF by rotating the VOL +/- knob.
BEEP ON/OFF
You can select two types of confirmation beep by rotating the VOL +/-
knob.
BEEP ON: The confirmation beep can be heard whenever a button is
pressed.
BEEP OFF: The confirmation beep is switch off.
SEEK 1/ 2 (only available during radio operation)
Seek function with the or buttons during radio operation.
You can select SEEK 1/ SEEK 2 by rotating the VOL +/- knob.
SEEK 1: Keep the or buttons pressed down and the radio will
stop at the next station that is detected.
SEEK 2: As long as the or buttons are pressed down the search
function will continue in the frequency band.
VOL LAST/VOL ADJ
You can select VOL LAST or VOL ADJ mode by rotating the VOL +/- knob.
VOL LAST: The radio switches on at the actual volume it had when
it was last switched off.
VOL Addition: Rotating the VOL +/- knob you can pre-select a constant
switch-on volume.
4. POWER ON/OFF
Turn the power on by using any button except the OPEN and REL button
and the VOL +/- knob on the front control panel; Press PWR button and
hold for approximate two seconds to turn power off.
Press the PWR button repeatedly to adjust the brightness of the VFD.
5. VFD Display
6.7. TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONS
a) During RADIO mode:
press the or button briefly to tune a frequency manually.
Press the or button and hold for more than one second to start
the automatic search for a radio station with a strong signal level.
(See also the function SEEK 1/SEEK 2.)
b) During CD/MP3 mode:
press the button briefly to play next track. Press the button
briefly to play the current track from the beginning of the current track.
Press the button twice continuously to play the previous track.
Press the or button hold to skip forward or backward.
8. BAND BUTTON
Press the BND button briefly to select the radio broadcasting band you
would hear.
TROUBLE SHOOTING
Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.
Common Symptoms
There is no power.
The CDs cannot
be loaded.
Cause
The fuse has blown.
Presence of CD disc inside the player
Inserting the disc in upside down
The surface of CD is extremely dirty
or it is damaged.
Temperature inside the car is too
high.
The volume control is set too low.
There is no sound.
The operation keys
do not work
The sound of the
CD player skips
The antenna cable is not connected. Insert the antenna cable firmly into the
antenna socket of the device.
No radio reception.
1.The built-in microcomputer is not
operating properly due to noise
2.Front panel is not properly fix into
its place
1. Switch the device off and on again. Or press
the RESET button to resume the program.
2. Reinstall the front panel
The device has not been correctly
connected.
The installation angle is more than
30 degrees
Wait until the road becomes smoother before
playing the CD.
Adjust the installation angle to less than 30
degrees
Turn up the volume properly.
Check the power and earth connection
according to the wiring diagram.
Cool off until the ambient temperature returns
to normal
Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.
Insert the compact disc with the label facing
upward
Remove the disc in the player then put a new
upward
Replace another fuse according to the wiring
diagram.
The car ignition is switched off.
If the power supply is properly connected to
the car accessory, switch the ignition key to
ON or " ACC " " " .
Solution
The device does
not work correctly
(EJECT, LOAD,
PLAY)
In automatic search
mode the radio does
not stop at a trans-
mitting station.
Tune in to a radio station manually.The transmission signals are too
weak.
The CDs are loaded
only halfway into
the CD tray.
The transport screws have not been
removed.
Remove the transport screws before using.
The surface of the road is uneven.
The surface of CD is extremely dirty
or it is damaged.
Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.