RCA 20F510TD TV DVD Combo User Manual


 
The Remote Control 5
The Remote Control
Digital Audio Out/Coaxial Jack
Use this jack to connect your TV/DVD Player to a Dolby* Digital or DTS receiver or decoder.
*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
DTS is a registered trademark of Digital Home Theater Systems, Inc.
Front Panel Controls (from left to right)
If you cannot locate your remote, you can use the front panel buttons of your TV to operate many of the
TV/DVD’s features.
POWER Turns the TV/DVD on and off.
PLAY/PAUSE Starts and pauses disc playback.
STOP Stops disc playback.
REV. (Reverse) Searches backward through a disc while it is in play mode. Press and hold remote control to
go to the previous chapter.
FWD. (Forward) Searches forward through a disc while it is in play mode. Press and hold to advance to the
next chapter.
OPEN/CLOSE Opens and closes the disc tray.
INPUT Toggles through the Video Input Channels [TV (AIR/CABLE), AV1 (SVID), DVD, AV3 (side front)].
MENU Brings up the PICTURE menu.
VOL q Decreases the volume. In the menu system, acts like the left arrow button on the remote control and
adjusts menu controls.
VOL p Increases the volume. In the menu system, acts like the right arrow button on the remote control and
adjusts menu controls.
CH q Scans down through the current channel list. In the menu system, acts like the down arrow button on
the remote control and adjusts menu controls.
CH p Scans up through the channel list. In the menu system, acts like the up arrow button on the remote
control and adjusts menu controls.
Putting Batteries in the Remote
Remove the cover of the battery compartment. Insert batteries, with the polarities as indicated, inside the
compartment. Replace the cover.
Note: If you are not going to use the remote for a long period of time, remove the batteries to avoid damage due to
leakage.
The Buttons on the Remote Control
INPUT Press it to switch between AV/DVD input and RF (antenna) input.
TV Press to place the remote control in TV mode.
MUTE Press to reduce the volume level. Press again to restore the volume.
DISPLAY Press to display channel information
PICTURE Press to display the picture preset.
SLEEP Press to set the sleep timer.
RECALL Press to return to the previous channel. If the unit is in menu mode, press
the RECALL button to the return previous menu screen.
POWER Press to turn the TV on or off.
VOL (left and right) buttons Press to increase or decrease the TV volume.
CH (up and down) buttons Scans up or down through the current channel list.
Press once to change the channel up or down, press and hold to continuously
channels. If your TV is in standby mode, press these buttons to turn the TV on. In AV
mode, press these buttons to switch to TV mode.
MENU Displays the TV’s Main menu (see page 7 for details).
0-9 (Number buttons) Press these buttons to select channels and to set the time
directly. Press 0-9 to select a channel. For example, to select channel 10, press 1 and
0, the channel changes. If you press 0 first, when you press the second number, the
channel changes at once. For example, to select channel 8, press 0 and then 8, the
channel changes immediately.
AUDIO Choose from four preset audio settings (MEMORY, STANDARD, NEWS or
MUSIC).
MTS/SAP This button is not available for this model.
Other buttons: Buttons other than the ones listed above, are not available for TV
functions.
Arrow buttons
for the TV Menu
System
INPUT
RECALL
POWER
MUTE
TV
SLEEP
MTS/SAP
DISPLAY
PICTURE
AUDIO
REPEAT
TITLE
SKIP
ANGLE
AUDIO
SUBTITLE
GUIDE
PBC
INFO
ZOOM
OK
VOL
VOL
CH
CH
DVD
MENU