Filter
Top Products
English - 36
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
2 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the
ENTER button.
3 Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
4 Press the EXIT button to exit.
➢
When the receiver is set to On, you can listen to the TV sound through the
2-channel receiver.
➢
If the receiver is exclusively for a home theater only (supporting audio only),
it may not appear in the device list.
➢
In case of a content with copyright problem, listening through the receiver may not properly operate.
➢
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
Check Points before Requesting Service
Symptom Solution
Anynet+ does not work. ■ Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■
Check the Anynet+ device’s Video/Audio/HDMI Cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI cable, please make sure
to search devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+. ■
Check if the Anynet+ device is properly connected to the TV and check
if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.
■
Press the TV button on the TV remote control to switch to TV. Then
press the TOOLS button to show the Anynet+ menu and select a
menu you want.
I want to exit Anynet+. ■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■ Press any of P, CH LIST, PRE-CH, and such to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet+ device is not connected.)
The Connecting to Anynet+
device… message appears
on the screen.
■ You cannot use the remote control when you are configuring
Anynet+ or switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to
view mode is complete.
The Anynet+ device does
not play.
You cannot use the play function when an auto channel scan is in
progress. Stop the currently running function.
The connected device is not
displayed.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI Cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI Cable only.
Some HDMI cables may not support Anynet+ functions.
The TV program cannot be
recorded.
Check whether the antenna jack on the recording device is properly
connected.
Enter
Move
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver :On
Setup
TV P 1
Return
책1.indb 36 2008-03-17 오후 4:21:45