Filter
Top Products
14
PICTURE-IN-PICTURE (PIP) OPERATION
For PIP to function you must connect two signals to the TV. (Use the TV’s 75 ohm input and
A/V inputs.) Connect VCR (or other accessory equipped with a video output jack) to the
TV’s audio video jacks as shown on page 12. If you are using a satellite dish, you must
connect two receivers or a cable system or antenna with the satellite to use the PIP feature (see
page 13). For operation with Cable Box, see chart on page 15.
USING PIP TO VIEW TWO TV PROGRAMS
Note: The following steps correspond to numbers on the
art below.
1. Switch VCR and television ON.
2. Press PIP ON/OFF key.
Set VCR to TV mode, if necessary.
3. Select channel for big window.
4. Press SELECT key to select Video1 or Video2 screen.
5. Press VCR key.
Note: If the remote control cannot be programmed to operate your VCR, you must use the
VCR’s remote to perform VCR functions.
6. Select channel on VCR for small window.
USING PIP TO VIEW TV PROGRAM
AND PRERECORDED TAPE
Note: The following steps do not have corresponding
reference numbers on the remote control art.
1. Set TV channel to match output of VCR (Channel 3 or 4).
2. Insert prerecorded tape into VCR.
3. Press PLAY, if necessary (wait for tape to load).
4. Set VCR to TV mode.
Note: When the remote control is in the VCR mode, the
VIDEO MODE key works like the TV/VCR key
on the VCR.
5. Press SWAP key to view PIP image in big window.
QuickTips
■
PIP window is black
with no
picture:
1. Check cable
connections.
2. Make sure VCR is
turned on.
3. Select another
channel on your
VCR.
■
Same picture appears
in Big and Small
windows. Set VCR
to TV mode.
■
To view two TV
programs or watch
a TV program and
prerecorded tape at
the same time, follow
steps on this page
and chart on page 15.
PIP KEYS
■
Use the SWAP key to
exchange programs
between the windows.
■
Use the LOCATION
key to change the
position of the small
window (Top: L/R or
Bottom: L/R).
■
Use the
QUIKFREEZE
key to stop the
action (see page 15).
■
Use the SELECT key
to choose the PIP
video source (Video1,
Video2, or TV RF
Signal).
VCR set to VCR mode.
Same image appears in
both windows.
VCR set to TV mode.
Different images appear
in each window.
CH
MENU RECALL
CAPTION SLEEP
1
4
7
0
8
5
2 3
6
9
RESET
VIDEO
MODE
POWER
CABLEVCR TV
REC STOP PAUSE
PLAY
MUTE DISPLAY
VOL
VOL
V-GUIDE
PIP ON/OFF
SWAP LOCATION
SELECT
QUIK
FREEZE
❺
❸
❻
❷
❹
❶
(Continued on page 15.)
PICTURE-IN-PICTURE (PIP) OPERATION
For PIP to function you must connect two signals to the TV. (Use the TV’s 75 ohm input and
A/V inputs.) Connect VCR (or other accessory equipped with a video output jack) to the
TV’s audio video jacks as shown on page 12. If you are using a satellite dish, you must
connect two receivers or a cable system or antenna with the satellite to use the PIP feature (see
page 13). For operation with Cable Box, see chart on page 15.
USING PIP TO VIEW TWO TV PROGRAMS
Note: The following steps correspond to numbers on the
art below.
1. Switch VCR and television ON.
2. Press PIP ON/OFF key.
Set VCR to TV mode, if necessary.
3. Select channel for big window.
4. Press SELECT key to select Video1 or Video2 screen.
5. Press VCR key.
Note: If the remote control cannot be programmed to operate your VCR, you must use the
VCR’s remote to perform VCR functions.
6. Select channel on VCR for small window.
USING PIP TO VIEW TV PROGRAM
AND PRERECORDED TAPE
Note: The following steps do not have corresponding
reference numbers on the remote control art.
1. Set TV channel to match output of VCR (Channel 3 or 4).
2. Insert prerecorded tape into VCR.
3. Press PLAY, if necessary (wait for tape to load).
4. Set VCR to TV mode.
Note: When the remote control is in the VCR mode the
QuickTips
■
PIP window is black
with no
picture:
1. Check cable
connections.
2. Make sure VCR is
turned on.
3. Select another
channel on your
VCR.
■
Same picture appears
in Big and Small
windows. Set VCR
to TV mode.
■
To view two TV
programs or watch
a TV program and
prerecorded tape at
the same time, follow
steps on this page
and chart on page 15.
PIP KEYS
■
Use the SWAP key to
exchange programs
between the windows.
■
Use the LOCATION
MENU RECALL
CAPTION SLEEP
1
4
7
0
8
5
2 3
6
9
RESET
VIDEO
MODE
POWER
CABLEVCR TV
❺
❻
❶