Filter
Top Products
Settings and Adjustments
36
GB
Settings for Sound (INITIAL
SETUP 2)
Select “
2
” after pressing SET UP.
“INITIAL SETUP 2” allows you to set the sound
according to the playback conditions.
Default settings are underlined.
pTRACK SELECTION
Gives the MPEG AUDIO and the Dolby Digital (AC-3) format
priority when you play a DVD on which multiple audio
formats are recorded. If multiple audio channels are recorded
in MPEG AUDIO or Dolby Digital (AC-3) format, the higher-
numbered channel audio recorded in MPEG AUDIO or Dolby
Digital (AC-3) format is played.
• OFF: No priority given.
• AUTO: Priority given.
Notes
• When you set this item to “ON”, the language may change
depending on the “AUDIO” settings in “LANGUAGE
SETUP.” The “TRACK SELECTION” setting has higher
priority than that of “AUDIO” settings in “LANGUAGE
SETUP” (page 34).
• If the number of the highest channels of the MPEG AUDIO
sound tracks is the same as the one of the DOLBY DIGITAL
(AC-3) sound tracks, the priority is given to the MPEG
AUDIO sound tracks.
• Depending on the DVD, the audio with priority may be
predetermined. In this case, you cannot give priority to the
MPEG AUDIO or Dolby Digital (AC-3) format by selecting
“AUTO.”
pSURROUND
Switches the mixing down methods when you play a DVD on
which the sound in Dolby Digital (AC-3) format is recorded.
• ON: when the player is connected to an audio component
that conforms to Dolby surround, Dolby Pro Logic
surround, etc.
• OFF : when the player is connected to a normal audio
component.
pDIGITAL OUT
Switches the methods of outputting audio signals from the
DIGITAL OUT OPTICAL and COAXIAL connectors on the
rear panel of the player.
• PCM: when the player is connected to an audio component
without a built-in MPEG AUDIO or Dolby Digital (AC-3)
decoder.
If you play the MPEG AUDIO or the Dolby Digital (AC-3)
sound tracks, the output signal is stereo. You can select the
surround effect by setting the item “SURROUND” to “ON”
or “OFF.”
• MPEG: when the player is connected to an audio
component with a built-in MPEG AUDIO decoder.
If you play the Dolby Digital (AC-3) sound tracks, the
output signal is stereo.
• DOLBY DIGITAL: when the player is connected to audio
component with a built-in Dolby Digital (AC-3) decoder.
If you play the MPEG sound tracks, the output signal is
stereo.
• DOLBY DIGITAL/MPEG: when the player is connected to
audio component with a built-in Dolby Digital (AC-3)/
MPEG AUDIO decoder.
The player outputs the appropriate signals automatically,
when you play a DVD.
Note
Select the setting correctly. Otherwise, no sound or
strange sound will come out from the speakers,
affecting your ears or causing the speakers to be
damaged.
pAUDIO DRC (Dynamic Range Control)
Makes the sound clear with the volume turned down at night,
etc. when you play a DVD. This affects the output from the
DIGITAL OUT connectors when “DIGITAL OUT” in
”INITIAL SETUP 2” is set to “PCM,” the output from the
LINE OUT (AUDIO) and EURO AV (1, 2) connectors.
• OFF: Normally select this position.
• ON: makes the sound clear even if you turned the volume
down.
Note
When you play DVDs without the AUDIO DRC function,
there may be no effect on the sound.
pAUDIO ATT (attenuation)
Selects the setting of the output from the LINE OUT (AUDIO)
and EURO AV (1, 2) connectors according to audio equipment
to be connected.
• OFF: turns off the audio attenuation.
• ON: reduces the audio output level so that no sound
distortion occurs.
Note
The setting does not affect the output from the DIGITAL OUT
connectors.
pAUDIO FILTER (DVP-S715 only)
Selects the type of digital filter to reduce the noise higher
frequency than 22.05kHz (fs 44.1kHz), 24kHz (fs 48kHz) or
48kHz (fs 96kHz).
• SHARP: makes the sound clear and provides smooth sound
reproduction. Normally set this position.
• SLOW: makes the sound warm and deep.
Note
Depending on the disc, there may be no effect on the sound.
INITIAL SETUP 2
SURROUND: ON
DIGITAL OUT:
AUDIO DRC:
PCM
OFF
QUIT
ENTER SETUP
OFFAUDIO ATT:
AUDIO FILTER:
TRACK SELECTION:
SHARP
OFF
1 2