Sony RMPJHS1 Universal Remote User Manual


 
1-10
VPL-HS1
19
GB
Menu Configurations
Using the Menus
Menu Items
Adjustable items are limited according to the input signals. Items that cannot be adjusted are not displayed in the
menu. (1 page 42)
Menu Item Description
PICTURE
CTRL
CONTRAST The higher the setting, the greater the contrast. The lower the setting, the lower
the cotrast.
BRIGHT (brightness) The higher the setting, the brighter the picture. The lower the setting, the darker
the picture.
COLOR The higher the setting, the greater the intensity. The lower the setting, the lower
the intensity.
HUE The higher the setting, the more greenish the picture becomes. The lower the
setting, the more purplish the picture becomes.
SHARP (sharpness) The higher the setting, the sharper the picture. The lower the setting, the softer
the picture.
RGB ENHANCER Adjusts the picture sharpness when computer signals are input.
D. (Dynamic)
PICTURE
ON: Emphasizes the black color.
OFF: Reproduces the dark portions of the picture accurately, in accordance
with the source signal.
GAMMA MODE GRAPHICS: Reproduces the photos in natural tones.
TEXT: Contrasts black and white. Suitable for images that contain lots of text.
COLOR TEMP HIGH: Gives the white colors a blue tint.
MIDDLE: Gives the white colors a neutral tint.
LOW: Gives the white colors a red tint.
COLOR SYS (System) Select the color system of the input signal.
AUTO: NTSC
3.58
, PAL, SECAM and NTSC
4..43
(switched automatically).
Normally, set to this position.
PAL-M/N: PAL-M/PAL-N and NTSC
3.58
(switched automatically).
When the PAL-M, PAL-N or NTSC
3.58
signal is input with COLOR SYS
set to AUTO, set to this position if the picture is distorted or colorless.
VOLUME Adjusts the volume. It can be adjusted for each of the inputs selected with the
INPUT button.
INPUT
SETTING
DOT PHASE When a signal from a computer is input, adjusts the picture for clearer picture
after the picture is adjusted by pressing the APA button.
SIZE H When a signal from a computer is input, adjusts the horizontal size of the
picture. The higher the setting, the wider the picture. The lower the setting, the
narrower the picture.
SHIFT As the setting for H (horizontal) increases, the picture moves to the right, and as
the setting decreases, the picture moves to the left. Use < or , to adjust the
horizontal position.
As the setting for V (vertical) increases, the picture moves up, and as the setting
decreases, the picture moves down. Use M or m to adjust the vertical position.
SCAN CONV (Scan
converter)
ON: Displays a computer signal according to the screen size. The picture will
be slightly softer.
OFF: Displays a computer signal as it is input. The picture will be clear but the
picture size will be smaller.
Note
When SVGA or XGA signal is input, this item will not be displayed.
ASPECT 4:3: Select when the 4:3 aspect ratio picture is input.
16:9: Select when the 16:9 aspect ratio picture (sqeezed) is input from
equipment such as a DVD player.
GB
18
Menu Configurations
Using the Menus
4
Make the setting or adjustment
on an item.
When changing the adjustment level
To increase the value, press M or ,.
To decrease the value, press m or <.
Press ENTER to restore the original screen.
When changing the setting
Press M or m to change the setting.
Press < or ENTER to restore the original
screen.
To clear the menu
Press MENU.
To reset items that have been
adjusted
Select the item you want to reset, then press RESET.
Complete! appears on the screen and the setting is
reset to its factory preset value.
Items that can be reset are:
CONTRAST, BRIGHT, COLOR, HUE, SHARP
and RGB ENHANCER in the PICTURE CTRL
menu
DOT PHASE, SIZE H and SHIFT in the INPUT
SETTING menu
DIGIT KEYSTONE in the INSTALL SETTING
menu
Menu
Configurations
The projector is equipped with four menu pages. The
items that can be adjusted in each menu are described
on pages 19 and 20.
PICTURE CTRL menu
The PICTURE CTRL menu is used for adjusting the
picture. You can also adjust the volume with this
menu.
INPUT SETTING menu
The INPUT SETTING menu is used to adjust the
input signal. You can adjust the size and position, etc.
of the picture.
SET SETTING menu
The SET SETTING menu is used for changing the
settings of the projector.
INSTALL SETTING menu
The INSTALL SETTING menu is used for correcting
distortion. You can change the display position,
intensity of the background picture, etc., of the menu
screen.
ENTER
SET SETTING
S TATU S :
INPUT-A:
LANGUAGE
:
POWER SAVING
:
VIDEO 1
ON
COMPONENT
ENGLISH
ON
or